Manipulator positioners are generally divided into compound positioners, single-axis positioners, double-axis positioners and three-axis positioners according to the number of components of the drive motor. Before and during the welding operation of the robotic arm, the positioner loads and locates the welded workpiece by clamping the stuff.

A lightweight cobot is an industrial robot with a flat, small touchscreen user interface that allows the user to control the robotic arm by instructing the movements on the screen. Perhaps, by holding the robotic arm easily, the desired path of movement is displayed. The interface fits most industrial sensors and ...

Motion control is closely related to robots. Robots in industrial applications need to move themselves through actuators composed of multiple motors to perform their mission or to grasp tools through a robot arm. The motion control system of the robot is usually composed of a motor controller, a motor drive, ...

Step 1: Teach function Convert the operation method to "T1" and move the robot to its origin position. Select the program "Cor_T1". Then open the folder (menu "Program" --> "FOLD" --> "AllFOLDs opn"), otherwise the corresponding entry will not be displayed ...

Before the KUKA robot is put into operation for the first time, it is necessary to carry out a review to ensure that the equipment and equipment are intact and functional, that they can operate safely and that faults can be identified. It is necessary for us to comply with the labor protection regulations of the country and region to check, and it is also necessary to test all safety ...

1. Place the nut Clamp the quad or hex nut and place it in the fixture 2. Thread sizing Grab the screw and assist it to complete the "180-degree turn" action; Apply an appropriate amount of sealant to the thread on its underside ...

Introduction to Logic Programming Use input and output in logic programming In order to communicate with the peripherals of the robot control system, digital and analog inputs and outputs can be used. To KUKA ...

The KUKA robot program is operated in several different ways and can be selected on the teach pendant. 1. By clicking on the "Program Operation Method" icon, you can check and select different methods Second, the program operator ...

KUKA robot circuit board repair, for the equipment that has not undergone the function of the online test, some test instruments also provide a less formal but more useful treatment: because the power supply of the test instrument to the robot circuit board can also be applied to the corresponding power supply and ground of the equipment through the test clip.

KUKA robot protective clothing is divided into a variety of types, different types have different functions, anti-static, dustproof, waterproof, etc. Here is a detailed introduction to the different types of robot protective clothing provided by Hongsheng Decheng, different characteristics and protective functions. ...

1. According to the equipment method, it is divided into: straight equipment and horizontal installation. The company uses drones, automation, robotics and artificial intelligence to leverage these important warehouse goals to better serve its customers while improving its bottom line. ...

1. Before replacing the KVGA, the following preparations must be made: 1. The robot control system must be in a shutdown state and maintained to avoid unauthorized accidental restart. 2. The buffer is turned off. 3. Put the feeder cable in a powerless state. ...

When calibrating at zero point, it is not necessary or advisable to disassemble the load things; Otherwise, the TCP may have to be recalibrated after disassembling and assembling things. In practice, it is possible to carry out the zero-point proofreading operation after the installation of the robot is completed. However, in the future, when you re-calibrate the zero point or check the zero point, you will ...

1. Red Dot Award for Exterior Design, all-aluminum structure, high strength, and therefore large load, KUKA already has a robot with a load of 1000kg, which can be seen at every exhibition. ​ 2. Complete the robot with six axes that can be quickly electronically corrected ...

One: The switch jumps often and may not be able to close? 1. Aging of switches 2. The switch selection is incorrect 3. The pump is stuck or the motor is short-circuited 4. The line is aging, short circuit, and the line is too small or lacks phase. Solution: Turn off the power of the control system...

The gear unit is a very important component of KUKA robot equipment. It has very important features and benefits. The main purpose is to support the mechanical rotating body and reduce the mechanical rotating body. The coefficient of friction is increased, the rotation accuracy is higher, and the service life of the machinery and equipment is longer. So how daily ...

First, the problem phenomenon 1. After the robot is powered on, the A5 axis can only move at a scale of -60-+60 degrees, but the teaching pendant is -120-+120 degrees; 2. From the 'Assist' of the Teach Pendant > 'About' a > 'Robot' to view the robot type, and the robot itself.

Each sensor on the seven axes of the KUKA robot LBR IIWA records everything that touches with the partner to ensure safety when assembling the DQ 200 automatic transmission, which requires several high-precision tasks in the manufacture of the transmission. This is not news for Škoda Auto. ŠkodaAuto ...

After each change to the motion command, the robot program must be tested at low speed (run method T1). Immediately starting a robot program at high speed can cause damage to the robot system and the entire equipment, as unpredictable movements may occur. If someone sits dangerously ...

1. Rapidity The time between the motor obtaining the command signal and the completion of the required working condition of the command should be short. The shorter the time of echoing the command signal, the higher the sensitivity of the electric servo system, and the better the fast response function.

Manipulator positioners are generally divided into compound positioners, single-axis positioners, double-axis positioners and three-axis positioners according to the number of components of the drive motor. Before and during the welding operation of the robotic arm, the positioner loads and locates the welded workpiece by clamping the stuff.