Steps to replace a KVGA graphics card with a KUKA robot

1. Specification: KUKA robot proofreading settings, KUKA robot calibration with or without load at the zero point of the robot mechanic. KUKA Robot Proofreading View Check to see if the KUKA robot school is correct about this orientation, if you don't grasp this orientation is correct or need to change it...

KUKA Industrial Robots is one of the world's leading manufacturers of industrial robots. More than 10,000 industrial robots are produced every year, and so far, 150,000 have been installed worldwide. Cooka is able to provide standard industrial 6-axis robots from 3KG to 1000KG, as well as some special purpose robots ...

The Cooka teach pendant is an interface between the supervisor application software and the user (robot). The teaching program is connected to the control cabinet by cable. When the robot performs actions such as jog feeder, program creation, program test execution, action execution, and attitude confirmation, we make ...

1. High production efficiency This is because the extension length of the wire is small when KUKA robots perform submerged arc welding, so a large welding current can be selected. For example, when electrode arc welding uses electrode welding, the current range is 250 - 350A, while submerged arc welding is usually 600? 850A， ...

The teaching pendant, also known as the teaching programmer or teaching box, is a hand-held device for manual operation, program writing, parameter equipment and monitoring of the robot; It is the core component of the robot control system, and is a device used to register and store mechanical movement or processing memory.

In order to improve the welding attainability, the arc welding workstation usually uses a variety of positioners, and the common formforms of positioners include L-shaped positioners, tipping positioners, headstock positioners, etc. In the meantime, the L-type positioner and the tilting positioner have two external shafts, and some special working conditions require ...

1. According to the mode of movement, it can be divided into: wheeled mobile robots, walking mobile robots (single-legged, double-legged and multi-legged), crawler mobile robots, creeping robots, peristaltic robots and swimming robots; ...

In the process of long-term use of KUKA robots, with the increase of operation time, various parts and parts will present various problems due to the influence of many factors such as friction, corrosion, vibration, impact, bumps, etc., so only by dealing with these problems and insisting on the normal operation of the robot can ...

In order to complete high-quality and high-efficiency welding, it is necessary to promote advanced welding technology and welding automation technology in the manufacture of nuclear power equipment. The head of the nuclear power pressure vessel is composed of a hemispherical head intersected with a plurality of round pipes, and its weld groove is a J-shaped groove. Because of the limitation of the spatial location, the weld of the structure ...

(1) The power supply voltage is too high; (2) The power supply voltage is too low, the motor is running with rated load, and the current is too hot for the winding; (3) When repairing and removing the winding, the thermal dismantling method is not appropriate, and the iron core is burned; (4) The motor is overloaded or starts frequently; (5) Lack of phase of the motor ...

(1) Open the program Open the newly created program file banyunl" and enter the program editor. There are 4 lines of program in the program editor, in between, INI: initialization, END: program completion, and the middle two lines return to the HOME point. (2) Teaching: return to the HOME point Use...

1. Power supply in front of the device The high rate of defects in the power supply during the programming of the KUKA robot is the entire faulty device, so it is easy to overhaul the power supply first Multiplier. 2. First the general and then the special Faults caused by the quality of assemblies or other equipment faults are common.

1. Schematic diagram of button indicator 2. Industrial robot QF1 This button is the power switch of the industrial robot control cabinet. 3. Power supply for industrial robots The power indicator indicates the power of the industrial robot control cabinet.

The drive control system is mainly used to control the robot to move according to the set motion parameters. It primarily consists of servo drives, servo motors and manipulators. (1) The servo motor is mainly used to drive the joints of the robot, and it is required to have ...

Disadvantage 1: When loading software components, the control system is stuck. Causes: The MFC device cannot be initialized, MFC3 is not properly plugged in, and the PCI bus on the motherboard is defective. Solution: Remove the PC card, boot the PC, check the MFC3 slot, and replace the control system PC. ...

1. Able to carry out high-precision packaging operations According to the integration of the stacking robot with other machinery and equipment, the intelligent robot can completely complete the original messy packaging operation, saving a lot of labor for the company and making due contributions to the company's intelligent production and production. ...

As a branch of industrial robots, KUKA SCARA robots are capable of installation, packaging, labeling, sorting and other processing technologies with their high precision, high cost performance, high flexibility and strong adaptability, helping many manufacturing enterprises to reduce staff and increase efficiency. But with the recent years of high-tech ...

1. Fault phenomenon: KUKA Robot Teach Pendant KRC4 The screen is out of order, and the mouse arrows do not move when touching the screen, and there is no change in orientation. 2. Causes: There are many reasons for the formation of this phenomenon.

KUKA welding robot has stable performance, large working space, fast moving speed, strong load capacity, and the welding quality is significantly better than manual welding, which greatly improves the production efficiency of spot welding operations. Spot welding machine is mainly used for spot welding of automobiles. 　　With the development of the automobile industry, butt welding ...

1) Comfort degree: This is an important goal that reflects the flexibility of the robot. Generally speaking, it is possible to reach 3 degrees of freedom in the robot working space, but welding must not only reach a certain position in the space, but also ensure the spatial attitude of the welding (cutting objects or welding tongs). Thus...