Carrying talents: Speak with strength The range of mass within which the robot can stand in any direction within its operating range. The load of the robot depends not only on the mass of the load, but also on the speed and direction of the robot. Bearer capacity refers to the load-bearing capacity when running at high speed. Bearing ability is not ...

Berthold Hermle AG is one of the world's leading manufacturers of milling machines and machining centers. When it comes to the automation of its machining centers, Hermle relies on the expertise of KUKA Roboter GmbH from Augsburg. In the new production system RS 4, the company ...

Fault 1: When loading a software component, the control system is stuck. Cause: The MFC device cannot be initialized, MFC3 is not properly plugged in, and the PCI bus on the motherboard is faulty. Solution: Remove the PC card, boot the PC, check the MFC3 slot, and replace the control system PC. ...

At present, the use of robots in machine tools by domestic enterprises is still in its infancy, and many theoretical and practical problems have not been fully understood and handled. For example, the most common form of use is still a simple combination of machine tools and robots, each using a set of control systems. To get the most out of the machine ...

1. In the main menu, select the > Measure > Thing > XYZ 4 points. 2. Give a number and a name for the thing to be measured. I admit it with a persistent key. 3. Use TCP to move to a reference point at will. Click Measure. Click Yes to reply to the security question ...

First, a single robot stamping and unloading: the robot will transfer the plate data from the palletizing table to the positioning table, and then transfer it to the stamping die for stamping after positioning, and after the stamping is completed, the data will be brought into the palletizing table through the robot, and the single pressure robot will be automatically loaded and unloaded. Second, robot stamping ...

Process 1: In the T1 form, the user program is pierced into cell.src according to the control requirements, the Cell.src program is selected, and the robot operation mode is switched to ExT_ AUTO. Process 2, under the condition that there is no error in the robot system, PLC-. Powering up, it's going to announce to the robot Smove_ en ...

1. Reasons for zero point failure: Before analyzing the cause of zero-point failure, let's first clarify a problem. For a long time, we have been calling this failure "zero point drop", which is an inaccurate depiction. The KUKA robot zero parameter does not "drop", it is recorded ...

back-up controller memory; Supervise the robot at regular intervals to view the robot, wires and cables; Look at the brakes; See how compact the robot is; listen to sounds, vibrations, and noise; Depending on the specific ...

Industrial manipulator arm is a new type of mechanical equipment in mechanization and automatic production, in the process of automatic production, the use of a kind of automatic equipment with grasping and moving, mainly in the process of simulating human actions to complete the operation, like the replacement of personnel to transfer serious objects ...

In order to complete high-quality and high-efficiency welding, it is necessary to promote advanced welding technology and welding automation technology in the manufacture of nuclear power equipment. The head of the nuclear power pressure vessel is composed of a hemispherical head intersected with a plurality of round pipes, and its weld groove is a J-shaped groove. Because of the limitation of the spatial location, the weld of the structure ...

Switching the axes of the external kuka robot to the bit arrangement in an asynchronous form means switching the synchronous and asynchronous forms of the external axes Program example: $ ASYNC_AXIS='b1000' ​ Indicates the outer axis 1, 2, 3 from right to left ...

1. KUKA robot motor coil repair, leakage, burning, overcurrent, overvoltage, heating, hot starting, alarm, tripping, and weak work; 2. The servo motor is weak in magnetism repair work, and the low-speed (no-load) can be alarmed at high speed (operation); 3. The repair of the external shaft motor of the robot is encountered.

Why does the robot flutter when it is running? Please do the following: 1. Is it that the load data you entered is incorrect? If the load data is too high or too low, and the difference between the load and the practice load is too large, it will cause flutter! 2、 ...

1. The current of the single-phase transformer at no load is different from the main magnetic flux, and there is a phase parity aFe, due to the presence of iron current. The no-load current is a spire waveform due to the large third harmonic in it. 2. The flow in the armature winding of the DC motor is also the communication current. But its ...

With the proposal of Made in China 2025 and the country's strong support for high-end manufacturing, the development of China's robot industry is very agile, and industrial robots are constantly changing the customs of welding robots. Based on the ten-kilogram arc welding robot, with light weight, high stiffness and high speed functions, it is based on the ...

In a sense, the wire and cable production profession is a profession of data finishing and assembly. - The amount of data used is huge, and the data cost in cable products accounts for 80-90% of the total production cost; Second, there are many types and varieties of materials used, and the functional requirements are particularly high.

A robot can be equipped with a working space. The working space provides security for the equipment. There are two types of workspaces: 1. The working space is a forbidden area Only robots are allowed to operate outside of the workspace. ...

1. Fulfill X-Start to enter the boot application, in the boot application, click Settings, and the network connection dialog box appears. 2. If you choose not to use the IP address, please click not to use the IP address of the robot drive, if ...

At present, the battery of the KUKA robot has two device orientations, one on the cabinet door and the other under the cooling channel, and the battery is connected to the plug X305 on the control cabinet and maintained by fuse F305. The battery plug X305 has been unplugged from the CCU when the control system leaves the factory.

In the foreign capital to speed up the layout of China's parallel robot shopping mall, the domestic market is not to be outdone, with the advantage of cost performance and the development of new use areas, domestic parallel robots or will take the lead in opening the game with foreign capital. Now, most of the world's domestic parallel robots ...