Safety prompt for the KUKA robot to change the motion command

1. The KUKA robot does not supply power and has no response 2. KUKA robot 1-6 axis, any axis does not move, stuck 3. The KUKA robot crashes and the KUKA robot computer cannot be started and the computer does not respond 4、KU ...

EXAMPLE1: XP1.x = 200 ; The new X value at point P1 is 200mm XP1.z = 30*distance ; Calculate the new Z-value of P1 point PTP XP1 is assigned and moves to the new P1 position ; EXAMPLE2: ...

(1) If the rotor of a KUKA motor is unbalanced, and the dynamic balance of the motor rotor is defective or deteriorates after use, the same oscillation source as the "oscillation motor" will occur. (2) The twist of the hinge, the twist of the hinge is similar to ...

KUKA robot resolver-to-digital converters (RDCs) are used to collect motor orientation data. Up to 8 resolvers can be connected to the RDC. In addition, the temperature of the motor is measured and analyzed. EDS is used to store non-volatile data in RDC bins. ...

3D modeling of KUKA six-axis robots 1. Modeling of chassis box and servo motor. There are mainly box bases, small electric boxes, rotating arm motors, etc. 2. Modeling of large arm structures. There are mainly drive arm seats, large hands ...

Berthold Hermle AG is one of the world's leading manufacturers of milling machines and machining centres. When it comes to the automation of its machining centers, Hermle relies on the expertise of KUKA Roboter GmbH from Augsburg. The company is charging in the new production system RS 4 ...

Switching the axes of the external kuka robot to the bit arrangement in an asynchronous form means switching the synchronous and asynchronous forms of the external axes Program example: $ ASYNC_AXIS='b1000' ​ Indicates the outer axis 1, 2, 3 from right to left ...

Manipulator positioners are generally divided into compound positioners, single-axis positioners, double-axis positioners and three-axis positioners according to the number of components of the drive motor. Before and during the welding operation of the robotic arm, the positioner loads and locates the welded workpiece by clamping the stuff.

1. Fault phenomenon: KUKA Robot Teach Pendant KRC4 The screen is out of order, and the mouse arrows do not move when touching the screen, and there is no change in orientation. 2. Causes: There are many reasons for the formation of this phenomenon.

(1) If the rotor of a KUKA motor is unbalanced, and the dynamic balance of the motor rotor is defective or deteriorates after use, an oscillation source similar to an oscillating motor will occur. ​ (2) The lead screw is tortuous, and the lead screw is bent after the screw is bent ...

Speculative protection cannot be achieved overnight, but needs to be completed at multiple levels and gradually. The following are the three key steps to start implementing speculative protection in the production equipment, please consult the data application experts of Xiamen Wutong Bolian for specific plans and steps: ...

In the process of using industrial robots, the robot body is usually selected to meet the use conditions, and the end actuator is customized for different occupations and environments. Regarding the selection of the robot body, the primary selection principle is: useful load, use of ...

When there is a problem with the gear reducer, we should check it in time to deal with the fault, as long as we have a certain understanding of the problems that may occur in the gear reducer. Today's China Transmission Network Xiaobian mainly introduces how to deal with the noise of gear reducer. ...

Each sensor on the seven axes of the KUKA robot LBR IIWA records everything that touches with the partner to ensure safety when assembling the DQ 200 automatic transmission, which requires several high-precision tasks in the manufacture of the transmission. This is not news for Škoda Auto. ŠkodaAuto ...

For "online" measurement, the requirements consider that the components under test are affected by other parallel branches, and the measurement results should be analyzed and judged against the schematic diagram. "Offline" measurement requires the components or circuits under test to be repaired and desoldered from the entire circuit or printed board, which is more troublesome to operate.

Theoretical part about variables: 1. When a KUKA robot is programmed with KRL, a variable is a container of calculated values ("values") that are presented during the operation of the robot process in the ordinary sense. 3. Each variable is ...

Traditional six-axis industrial robots generally have 6 degrees of freedom, including rotation (S-axis), lower arm (L-axis), upper arm (U-axis), wrist rotation (R-axis), wrist swing (B-axis) and wrist rotation (T-axis). The 6 joints are combined to achieve the 6 degrees of freedom movement at the end. ...

KUKA robotic resolver-to-digital converters (RDCs) are used to collect motor orientation data. Eight resolvers can be connected on the RDC. In addition, the temperature of the motor is measured and analyzed. EDS is used to store non-volatile data in an RDC bin. ...

There is a program called BAS.SRC under the R1System in the KUKA robot program directory, which is mainly used to set the number of parameters related to the robot motion, such as coordinate system, velocity, acceleration, etc. One. Online forms Let's take a look at how to use the commonly used online form.

1. Maintain good parts Parts are an important part of CNC machine tool robots, the reason why the parts of CNC machine tool manipulators show severe wear and tear in the process of use, mainly because of the problems of people's devices, so that the position of parts is problematic.