1. Demand awareness: Robot model: e.g. KR16-2 System variety: e.g. KSS8.3.38 Option package: e.g. EthernetKRL 2.6 Control cabinet model: e.g. Smallsize-2; ...

1. Connect the oil pump to the discharge hose. 2. Increasing the required amount of oil through the discharge hose. 3. Clean the magnetic plug, check the seal, and replace the damaged magnetic plug. 4. Install the magnetic and tighten it; M ...

After the KUKA robot is turned on, the teach pendant displays KSS15101 fault code, which means that the five safety nodes of the safety device from 0 to 4 channels are wrong, and the robot cannot be put into normal operation. First of all, the KUKA robot is repaired ...

1. Enter the program in the form of the teach pendant T1, click on the lower left corner: Instruction - Logic, and you will see the commonly used logic instructions such as WAIT, WAITFOR, and OUT. 2. Select WAIT. The lower end of the interface *** presents the WAIT Time port sec .

In Arc StartV, the A directive is a condition for arc welding, i.e., after the tp program directly specifies the welding current and voltage or the delivery speed of the metal wire, the end welding is started. According to the setting of the equipment variety, imitation input and output ...

(1) If the rotor of a KUKA motor is unbalanced, and the dynamic balance of the motor rotor is defective or deteriorates after use, the same oscillation source as the "oscillation motor" will occur. (2) The twist of the hinge, the twist of the hinge is similar to ...

The KUKA controller KR C5 offers even more possibilities and cost-effectiveness in robotics applications Compact, high-quality, energy-efficient: KUKA has been tested with the new controller KR C5 for KUKA industrial robots and the corresponding small robot controller.

Phenomenon 1: The direction of the finger does not coincide with the mouse arrow. Reason 1: After the driver is installed in the industrial robot teach pendant, when correcting the bearing, there is no pen directly touching the square position of the bull's-eye. Treatment 1: Correct the orientation from the beginning. ...

1) Run the CELL.src program in T1 or T2 form, perform part (1) in the figure, the KUKA robot performs back to the HOME point, performs the BCO operation, the window displays "BCO has been reached", and the BCO operation makes the KUKA robot run to the track. ...

1. Do a load test and use it correctly in the program. 2. Replace all LIN and CIRC commands with SLIN and SCIRC 3. Delete the PTP movement instructions that are repeated at the point, and try to have as few transition points as possible 4. Can be used with the imminent ...

The 21st China International Industry Fair (CIIF) will be held at the National Convention and Exhibition Center (Shanghai) from September 17 to 21, 2019. At booth E025 in hall 8.1H, KUKA will bring a series of digital and intelligent robot products and application processing plans to the show! All along, KU ...

1. The underlying controller As the center of the control system, the selection of the underlying controller is very important to the whole system, and its performance directly affects the reliability of the control system, the speed of data processing, and the reliability of data collection.

(1) If the rotor of a KUKA motor is unbalanced, and the dynamic balance of the motor rotor is defective or deteriorates after use, an oscillation source similar to an oscillating motor will occur. ​ (2) The lead screw is tortuous, and the lead screw is bent after the screw is bent ...

1: KUKA Robot Teach Pendant Bad Contact or Partial Ineffective (Replacement Contact Panel) 2: KUKA Robot Teach Pendant does not appear (repair or replace the internal motherboard or LCD screen) 3: KUKA Robot ...

In the repair of circuit boards of industrial KUKA welding robots, it is necessary to be familiar with the damage characteristics of commonly used components and component detection methods 1. The resistor with small resistance value and the resistor with high power in the circuit board are easy to be damaged Small resistance values in the circuit board ...

KUKA has three divisions: (1) Robotics: including six-axis robots, medical machine factories, palletizing robots and other products; (2) System integration: provide solutions for automobile production, electronic processing, food processing and other industries; (3) Swisslog (Swisslog AG): KUKA ...

In recent years, KUKA has made a qualitative leap forward in robot skills, and the robot's performance has been continuously improved and adaptable. In order to ensure the service life of KUKA robots, KUKA robot dresspacks are widely used. With the continuous improvement of the robot system, the variety of pipeline packs is also increasing.

KUKA robot resolver-to-digital converters (RDCs) are used to collect motor orientation data. Up to 8 resolvers can be connected to the RDC. In addition, the temperature of the motor is measured and analyzed. EDS is used to store non-volatile data in RDC bins. ...

KUKA Robot External Active Configuration Tutorial - Interface Interface Description Description of the output variable There are a total of 4 menus for output signals; First, we will introduce the commonly used output signals $ALARM_STOP—Urgent abort ...

Once the phenomenon of the robot servo motor drive burning MOS tube is started, the external stable wire of the drive will be burned, and the equipment cannot be operated. When the repairer checked, he found that a power tube had been damaged, but because there was no material, he couldn't figure out the effect of the tube.

Before the first operation of an industrial robot, it is necessary to carry out a review to ensure that the equipment and equipment are flawless and functional, can operate safely and identify faults. It is necessary for us to abide by the labor protection regulations of the country and region where we are located to check, and it is also necessary to test all safety ...