KUKA robot startup steps

1. By clicking on the "Program Operation Method" icon, you can view and select different methods. 2. The operation methods of the program are [Go], [Action], and [Single Process]. 1. Go: refers to the uninterrupted connection of the program.

In order to improve the welding attainability, the arc welding workstation usually uses a variety of positioners, and the common formforms of positioners include L-shaped positioners, tipping positioners, headstock positioners, etc. In the meantime, the L-type positioner and the tilting positioner have two external shafts, and some special working conditions require ...

According to the use and development needs of KUKA welding robots, traditional welding methods cannot efficiently meet the production needs to a certain extent, and arc welding robot skills are increasingly valued by manufacturers. How to complete mass production efficiently and efficiently with arc welding robots is the most important thing to do.

1) Rapidity. The time from obtaining the command signal to the completion of the required working state of the motor should be short. The shorter the time to respond to the command signal, the higher the sensitivity of the electric servo system, and the better the fast response function.

1. KUKA's programming language KUKA'S ROBOT PROGRAMMING LANGUAGE IS KRL, WHICH IS A TEXTUAL LANGUAGE SIMILAR TO C LANGUAGE (PLEASE BAIDU WHAT IS C LANGUAGE), WHICH IS COMPOSED OF .SRC AND . DAT composition. . SRC stores program logic, instructions, actions, etc. DAT stores azimuth variables in the form of ...

What is tool load data? Tool load data refers to all the loads mounted on the robot flange. It is the mass that is additionally mounted on the robot and moved by the robot with it, and the values that need to be entered are mass, the center of gravity (the point at which the mass is affected by gravity.), the moment of inertia of the mass, and ...

In order to solve the pain points of welding professions, such as high variety, small batch, poor team consistency, harsh working environment, long commissioning time, and difficult changeover, KUKA Industry has launched a new treatment solution, Smart Welding. Smart Welding is developed in depth according to kuka.SimPro, offline programming without teaching, no ...

1) In addition to aligning TCP (or using digital analogue, is there a way to improve track accuracy? 2) There are cutting and other processes on site, which have high requirements for track accuracy, if the robot track presents the phenomenon of jitter such as sawtooth, how to deal with it? 3) ABB robot for ...

According to the application status and development needs of the welding technology of KUKA welding robots, the traditional welding methods must not be able to meet the production needs to a certain extent, and the arc welding robot technology has been paid more and more attention by manufacturers. How to complete the batch production of arc welding robots, is the current arc welding machine...

1. Scrub each axis of the robot. 2. Check the accuracy of TCP. 3. Check the residual level. 4. Check whether the zero position of each axis of the robot is accurate. 5. Clean the filter behind the water tank of the welder. ...

1.FORCE TORQUE CONTROL / SENSOR COMMUNICATION Choosing from a variety of KUKA signal processing software can be a small extension of your robot.

1) Comfort degree: This is an important goal that reflects the flexibility of the robot. Generally speaking, it is possible to reach 3 degrees of freedom in the robot work space, but the welding must not only reach a certain direction in the space, but also ensure the spatial attitude of the welding (cutting things or welding tongs). Thus...

1. The KUKA robot enters the program in the teach pendant T1 mode, clicks on Instruction - Logic in the lower left corner, and you will see the commonly used logic instructions such as WAIT, WAITFOR, and OUT. 2. Select WAIT, and the lower end of the interface presents the WAIT Time port sec.

The teaching pendant, also known as the teaching programmer or teaching box, is a hand-held device for manual operation, program writing, parameter equipment and monitoring of the robot; It is the core component of the robot control system, and is a device used to register and store mechanical movement or processing memory.

1. The current of the single-phase transformer at no load is different from the main magnetic flux, and there is a phase parity aFe, due to the presence of iron current. The no-load current is a spire waveform due to the large third harmonic in it. 2. The flow in the armature winding of the DC motor is also the communication current. But its ...

The new articulated arm robot KR SCARA is a reliable complement to KUKA's industrial production, whose primary strength is the assembly of small parts, the transfer of materials or the inspection of small parts. In this respect, few other robots in load classes below 6 kg are able to compete with the KUKA SCARA robot.

When you think of Oktoberfest, the smell of roasted almonds, a Ferris wheel, and a glass of beer immediately comes to mind. But what does KUKA have to do with it? Tradition and modernity Tomorrow at 12 noon sharp: as soon as the Tressienwi in Munich sounds "0'zapft i ...

In the process of using industrial robots, the robot body is usually selected to meet the use conditions, and the end actuator is customized for different occupations and environments. Regarding the selection of the robot body, the primary selection principle is: useful load, use of ...

KUKA palletizing robots are widely used to move goods to or from pallets (unloading palletizing) and to lift, palletize, pack, transport, sort and mark. This process is not only closely related to the wooden furniture industry, the food logistics sector, but also ...

The boundary of robot operation refers to the movement of parts and things in space through a certain organization, which naturally requires the expression of the orientation and posture of parts, things and the organization itself. In order to delimit and use the mathematical quantities that express poses, we must delimit the coordinate system and give the rules of expression. ...