Procedure for TCP correction of KUKA robots

Second, welding is a common name for "carbon dioxide gas maintenance welding", and argon maintenance welding (commonly known as "argon arc welding") and other gas maintenance welding are called "gas maintenance welding". The advantage of the second protection welding is that it is open arc welding, which is easy to achieve all-round semi-...

(1) If the rotor of a KUKA motor is unbalanced, and the dynamic balance of the motor rotor is defective or deteriorates after use, an oscillation source similar to an oscillating motor will occur. ​ (2) The lead screw is tortuous, and the lead screw is bent after the screw is bent ...

Fault Symptom: After the robot is turned on, the teach pendant shows KSS15101 fault code (the safety device is wrong in 5 safety nodes from 0 to 4 channels), and the robot cannot be put into operation normally. Fault Detection: First inspect the site ...

Routine safe operation and maintenance of KUKA welding robots. KUKA welding robot operation I must go through professional training, master the use of system indicators and buttons, and be familiar with the most basic equipment knowledge, safety knowledge and precautions before being able to take up the post. Before booting up KUKA ...

Introduction to logic programming, the input and output terminals are used in logic programming, and in order to communicate with the peripheral devices of the robot control system, digital and analog input and output terminals can be used. TO THE KUKA MACHINE ...

According to the application status and development needs of the welding technology of KUKA welding robots, the traditional welding methods must not be able to meet the production needs to a certain extent, and the arc welding robot technology has been paid more and more attention by manufacturers. How to complete the batch production of arc welding robots, is the current arc welding machine...

The six-axis industrial robot is a process test instrument used in the field of natural science related engineering and technology, and the common six-axis joint robot has six built-in servo motors, which directly drive the rotation of the six joint shafts through the reducer and synchronous pulley. Six-axis industrial robots generally have ...

KUKA industrial robots are generally classified according to centralized specifications: 1. Classification according to the number of axes. 2. Classification according to the use scenario. For example: welding, palletizing, etc. Model status of KUKA robots. ...

1. Robot selection An industrial robot is a complex system, including manipulators, control systems, programmers and other software and accessories. Before use, it is necessary to select according to the actual production requirements of the enterprise and choose the products suitable for their own production line. Selected Guideline Packet ...

KUKA iiQoT simplifies data-driven automation for businesses. To do this, the software uses the benefits of the Industrial Internet of Things (IIoT): it brings together the condition data of the entire robotics team, from hardware to software to controllers, in a single channel that is clear and unambiguous. KUKA ...

KUKA's Edition robot assists new customers in price-sensitive shopping malls in the useful automation of welding tasks. Focus on the main points, have a higher cost-to-benefit ratio, and can obtain the skill set at that time. Initially, the KR CYBERTECH nano ARC was available in two variants of the Editi ...

The main technical parameters of the robot are freedom, resolution, working space, working speed, working load, etc. The comfort of the robot refers to the number of independent motion parameters required to determine the orientation and posture of the robot's hand in space. The degree of freedom of the robot is generally equal to ...

First, the characteristics of parallel robots 1. No accumulated error, high accuracy; 2. The driving equipment can be placed on or close to the direction of the fixed channel, so that the moving part is light in weight, high in speed and has good dynamic response; 3. Compact structure, high stiffness and large bearing capacity; ...

At present, the use of robots in machine tools by domestic enterprises is still in its infancy, and many theoretical and practical problems have not been fully understood and handled. For example, the most common form of use is still a simple combination of machine tools and robots, each using a set of control systems. To get the most out of the machine ...

The robot control system is an important part of the robot, which is used to control the manipulator to complete specific work tasks, and its basic functions are as follows: 1. Recall function: store the order of work, the movement path, the movement mode ...

In the case of industrial robots and machine tools, it may involve the precise and harmonious movement of multiple axes in a specific space to complete the task at hand. Robots generally have 6 axes, and these axes must be harmonious and orderly, and if sometimes the robot moves along a trajectory, there will be 7 axes. ...

Before the first operation of an industrial robot, it is necessary to carry out a review to ensure that the equipment and equipment are flawless and functional, can operate safely and identify faults. It is necessary for us to abide by the labor protection regulations of the country and region where we are located to check, and it is also necessary to test all safety ...

1. Degrees of freedom and degrees of freedom are the main goals to measure the level of robotics. The so-called degrees of freedom refer to the independent motion of moving parts relative to a fixed coordinate system. Each degree of freedom requires a servo axis to drive, so the higher the number of degrees of freedom, the more chaotic the robot can complete the actions ...

Carrying talents: Speak with strength The range of mass within which the robot can stand in any direction within its operating range. The load of the robot depends not only on the mass of the load, but also on the speed and direction of the robot. Bearer capacity refers to the load-bearing capacity when running at high speed. Bearing ability is not ...

First, welding robot inspection and protection 1. Wire feeding arrangement. Including whether the wire feeding force is normal, whether the wire feeding tube is damaged, and whether there is an abnormal alarm. 2. Is the airflow normal? 3. Is the torch safety protection system normal? (It is forbidden to close the welding torch safety protection ...