1. Preparation before robot maintenance 1. Robot oil type: REO about 1000ml, EP2 about 10-30ml, WR2 about 10ml 2. Tools: one technical refueling pump, 4 syringes, oil blotting paper, several plastic bags, waste oil drums, hexagonal wrenches 3. Robot ...

Relying on the technology stack of OTC robots and the advantages of automation, OTC can create a set of automated operation systems for customers that use robots to realize from bolt picking to bolt locking agent application and tightening screws. This...

The robot control system is an important part of the robot, which is used to control the manipulator to complete specific work tasks, and its basic functions are as follows: 1. Human-machine interface: teaching box, operation panel, display screen. ...

With the acquisition of more and more users of OTC robots, the popularity is growing. At present, more and more factory users have begun to pay attention to OTC robot products, and everyone may have a simple or in-depth understanding of OTC robot products from the Internet or related exhibitions. ...

1. Shut down and restart. 2. After the shutdown and restart are invalid, remove the sequence board and reinstall it. 3. If it still doesn't work, switch the IPM board with other machines to verify whether it is Sequence...

1. 3 years warranty (body, control box, teaching box, operation box, control cable); 2. Full Chinese operation interface, simple and easy to understand, and can support 6 language selection; 3. The operating radius is long, and the operating radius of the standard welding robot can reach 1.4 meters or 2 meters (excluding the welding gun).

The robot HOME point is the starting point of the robot, and it is generally the end. In the window, click "robotkr210r2700_extra", and then under the "Commands" menu in the menu, click the command button RobotJog to guide the manual operation panel to open and move the robot to the appropriate ...

1. The arrangement and arrangement of the parking airport should ensure that the entry and exit of any manipulator is not affected by other manipulators. 2. It should be parked in a dry room. Those who have the necessary need to park outside should pick a flat ground and lay it with planks. After parking, cover with a covercloth. 3. In ...

(1) I/O port I/O input and inlet, including welding start, stop, reset, welding method selection, welding car and welding torch adjustment and other 16 switching inputs, plus pendulum photoelectric sensor switching input, sharing 17 I/O input points. I/O outputs, 3 ...

The high-voltage electrolytic capacitor C2 supplies a stable DC to the primary inverter transformer to ensure the stable operation of the OTC welding machine. However, since the electrolytic capacitor is the same as the battery, the electrolyte is encapsulated inside, and the consumption of the electrolyte cannot be completely avoided, and its life span is limited. Therefore, in order to ensure that the welding machine ...

Fault phenomenon: Manual operation is normal. After switching to automatic mode, the intermittent red light does not stop, but pressing strat once will make the program trek one step. Solution: Because the working mode of the machine is changed to one step intermittent, please ...

1. Adjust the arc voltage If the settings are incorrect, the voltage setting will significantly add to the spatter. The low voltage setting can cause spatter as the wire is repeatedly short-circuited in the weld pool, resulting in a small burst at the wire tip. This short circuit is normal for short arc MIG welding, but ...

The OTC arc welding robot has five optional special sensor accessories for arc welding, which are FD-WD, FD-AR, FD-QD, FD-QF, FD-QT. During this period, the introduction of each type of arc welding special sensor equipment is as follows: 1. FD ...

When the second-hand manipulator is stored for a long time, it is necessary to pay attention to the following seven requirements: 1. The arrangement and placement of the parking airport should ensure that the entry and exit of any manipulator is not affected by other manipulators. 2. It should be parked indoors in a boring room. Those who have to park outdoors should choose a flat ...

The process measures to reduce the welding stress and deformation of welding robots mainly include: 1. Heating "subtraction zone" method Before welding, the welding robot is heated in the area near the welding part (subtraction area) to make it elongated, and when it is cooled after welding, the heating zone is shortened together with the weld.

Communication between the welding robot and the welding machine: 1. Analog communication 2. Digital Communications Analog communication, generally directly connect the analog interface of the welding machine with the analog module of the robot (but also according to the requirements of the welding machine manufacturer, some welding machine analog communication needs to be added...

1. Stable center of gravity Welding is like practicing martial arts, the first thing to do is that the chassis should be stable, that is, the "horse step" should be stable, and the center of gravity cannot be unstable, and it is difficult to weld a good weld when the welding is shaking. 2. The welding torch should be stable Trembling words ...

E1064 Handling of Unstable Exceptions Detected in Sequential Circuits. 1. Shut down and restart. 2. After the shutdown and restart are invalid, remove the sequence board and reinstall it. 3. If it doesn't work ...

In the welding process, it is necessary for the robot to use the walking mode of interpolating straight lines or arcs to weld. The difficulty coefficient of welding arc is the highest, and whether the arc welding is beautiful or not is the true level of a welder. The robot welding arc first needs to be programmed, and the program should be ...

In China, under the background of deepening industrial transformation and upgrading, and weakening the profitability of the population, the scale of manipulator use is becoming more and more extensive, and industrial robots are rapidly entering the market with a high compound growth rate. The stamping manipulator can replace the body to complete the damage and repetitive monotonous work, and can also reduce the strength of human labor.

Contacts are one of the items that often replace welding materials. During this time, the contact fixes the direction of the wire, and since the instantaneous current that moves when the arc is closed after welding is too simple to melt the contact outlet, it must have a role. The wire and contacts have been welded together, so that the welding can no longer be performed ...