OTC Robot FD-B4 Maintenance Steps:

When the OTC robot is being used, the encoder battery low alarm cannot be recovered, and the encoder orientation information is lost, it is necessary to reset the operation: 52 encoder failure encoder battery charge lo ...

The hardware of the microcomputer control system of a welding robot is mainly composed of the interface circuit of the S7-200 PLC microcomputer manipulator and the sensors and motors. The S7-200 controller modules are: CPU module, I/O module, and D/A module ...

The OTC robot body is equipped with a battery for absolute. Back up encoder data. The life of the battery varies depending on the working environment, please replace the battery with a new one every two years. Otherwise, the coder data will be lost and the origin will need to be readjusted. Before the replacement operation, please back up the teaching data to ...

1. Whether the columns and upper and lower beams are deformed or distorted. 2. The deflection and deformation of the fork up and down, the wear condition of the guide surface and the guide wheel. 3. Whether all kinds of welded components and castings are cracked and corroded. 4. Bolts, ...

Replace the battery with a low voltage when the power is not interrupted. After that, the origin of each axis is reset. 1. Align the corner marks of each axis of the robot so that each axis of the robot stops at the origin position. If the servo cannot be powered on, ...

The general welding equipment is completely controlled by manual experience, so that the solder joints of the nut are high and low, and the output and power stability of the equipment are not ambitious, the phenomenon of false welding simply occurs. When welding nuts with general welding equipment, it is very simple to show detachment.

The OTC robot needs to adjust the tension of the belt once a year or every 3,000 hours of work, whichever is shorter. The OTC robot B4 (B4L) is used as an example to introduce the adjustment method and precautions. The timing belt of the OTC robot B4\B4L is located in the motor and reduction gear.

1. Pneumatic drive system The pneumatic drive system is generally composed of cylinders, valves, air tanks and air compressors (or directly supplied by the air pressure station). and so on, with compressed air to drive the execution of the organization to carry out the operation. Its advantages are convenient air source, agile action, simple structure, low cost, ...

(1) Read the welding process diagram to understand the information, equipment, things and related process parameters of the workpiece to be welded, including the selection of the appropriate welding machine (such as the AC welding machine required for welding aluminum alloy), the selection of the appropriate tungsten electrode and gas flow. First of all, understand the welding current and ...

In order to perform excellent manipulation of the robot, it is important to understand the characteristics of the controlled, and from what we know about the dynamics of the robot, it has the following characteristics: 1. The essence of the robot is a nonlinear system. There are many factors that cause nonlinearity in the robot, such as structure, transmission parts, etc.

Choose the right filler metal What is a base metal and what is the quality? We work with different metals because they have different properties and generally don't work well together. Apply the right application to match your base metal ...

OTC robots have certain advantages in all kinds of welding fields, and can complete all kinds of welding operations for users, which is a very good feedback and reputation for OTC robots. However, for users who do not know about OTC robots, they often may not know that OTC robots are used in various fields.

In recent years, China's industrial robot industry has entered a period of rapid growth, and has become the world's largest shopping mall for six consecutive years. In the development of industrial robots, there was a hot together, the concept of hype that existed at that time, rushed ...

The OTC arc welding robot has five optional special sensor accessories for arc welding, which are FD-WD, FD-AR, FD-QD, FD-QF, FD-QT. During this period, the introduction of each type of arc welding special sensor equipment is as follows: 1. FD ...

1. Rigid treatment. The influence of elastic deformation of the structure on the motion of the rigid body of the structure is completely ignored. For example, in order to avoid excessive elastic deformation from damaging the stability and terminal positioning accuracy of the flexible robotic arm, the maximum angular velocity of NASA's remote-controlled spaceman movement is 0.5deg/s. 2. Feedforward ...

1. Touching part The sensory part is like the five senses of human beings, providing a sense for the robot's operation and helping the robot's operation process to become more accurate. This part can be divided into two main systems: (1) Sensory system Feeling...

1. Why do I need to adjust the parameters at any time when welding stainless steel? When welding stainless steel, the primary reason why welders can adjust the welding parameters (voltage, current, arc length, induction coefficient, pulse width, etc.) at any time is the mismatched composition of the welding consumables. Chemical composition is important, and the batch...

Laser welding robot is a very popular automatic welding equipment in recent years, about many manufacturers who use argon arc welding machine, laser welding professional equipment is a new technical application, if you also want laser welding machine technical but do not know the details of today's general electric for us to interpret the excited...

1. Power cord: divided into internal filling and external filling. External filling lines are available for bottom and high current filling. The end of the wire is located at the front of the ramp and is fixed with the left hand, and it is fed into the weld pool for welding. There is almost no gap between males. Its advantages include high current, small aperture ...

OTC robots need to adjust the belt tension once a year or every 3000 hours, whichever is shorter. This article takes the OTC robot B4 (B4L) as an example to explain the adjustment methods and precautions. The timing belt of the OTC robot B4\B4L is located between the motor and the reduction gear, which is used to drive the J5 axis ...