E1064 Unstable Exception Handling in Sequential Circuits – Odich

1. The only warranty in the industry for 3 years (body, control box, teaching box, operation box, control cable); 2. Full Chinese operation interface, simple and easy to understand, and can support 6 language selection; 3. Long working radius, standard welding robot working radius up to 1.4 meters or 2 meters (not...

Interruption means that in the process of computer operation, when there is some unexpected situation that requires the intervention of the host, the machine can automatically stop the running program and transfer to the program that deals with the new situation, and return to the original suspended program to continue to run after processing. ...

Robot is a very complex system, there are many planning challenges in mechatronics, functionality and electrical, when planning the building blocks of the robot system, it is necessary to understand the needs of these aspects and select appropriate planning ideas. ...

The scientific PLC programming process is actually very simple, but often most engineers think it is simple and neglect many details. Negligence in details will inevitably lead to problems in the future. If you want to avoid problems in the future, you can only abide by the rules well, no rules are not a circle, PLC programming has its ...

1. Encoder own problem: It refers to the problem of the encoder's own components, resulting in its inability to generate and output correct waveforms. In this case, the encoder needs to be replaced or the internal equipment repaired. 2. Encoder connection cable problem: the probability of this problem is the highest, repair ...

1. The arrangement and arrangement of the parking airport should ensure that the entry and exit of any manipulator is not affected by other manipulators. 2. It should be parked in a dry room. Those who have the necessary need to park outside should pick a flat ground and lay it with planks. After parking, cover with a covercloth. 3. In ...

The installation method of the I/O board of the OTC welding robot relay device and the connection method of the general I/O wire are taken as an example of the OTCFD series robot. As we all know, the relay unit and the I/O board can be used together, and one control unit can connect more than two boards. If you buy an OTC welding machine at the same time ...

Customer Requirements: Due to the small working space, the robot needs to be installed close to the wall, or installed on the shelf or platform, saving the overall floor space! In addition, a robot system is needed to be able to complete the cutting of H-beams, improve the overall production efficiency, and improve the ...

There are three installation methods for robots applied to machine tool automation: "ground-mounted robot transfer" (island processing unit), "ground-mounted walking axis robot transfer" (machine tool placement in a straight line), and "crane walking shaft robot transfer" (machine tool placement in a straight line). All of them are capable of continuous ...

The servo motor is the driving device of the robot joint The joint drive of the robot is inseparable from the servo system, and the more joints, the higher the flexibility and accuracy of the robot, and the more servo motors need to be used. The servo motor affects the robot's arm control, such as orientation, angle, etc.

From the perspective of movement mode, parallel robots can be divided into plane organization and space organization; Subdivisions can be divided into planar moving organizations, planar moving rolling organizations, spatial pure moving organizations, spatial pure rolling organizations and spatial mixed motion organizations, and can also be classified according to the number of degrees of freedom of parallel organizations: ...

The general welding equipment is completely controlled by manual experience, so that the solder joints of the nut are high and low, and the output and power stability of the equipment are not ambitious, and the false welding phenomenon simply occurs. When welding nuts with general welding equipment, it is very simple to ...

Work space refers to the orientation mobilization of a specific part of the robot arm under certain conditions. The nature and size of the workspace reflect the size of the robot's working capacity. When understanding the robot's working space, pay attention to the following: ...

Industrial robot is a multi-joint manipulator or multi-degree of freedom intelligent machine device for the industrial category, which can perform work automatically, and is a kind of machine that relies on its own power and control ability to instigate various functions. Not only can it be commanded by humans, but it can also operate according to pre-programmed procedures.

1. The axis key that controls the movement of the junction is mainly used to adjust the orientation and angle of the robot and the welder. When the SW switch is pressed, the cooperative coordinates can be used to control the robot's orientation. 2. The coordinate switching button can be used to cut between axis coordinates, robot coordinates and tool coordinates.

1. Rapidity, the time from obtaining the command signal to the working state required by the completion of the instruction should be short. The shorter the moment of echoing the command signal, the higher the sensitivity of the electric servo system, and the better the fast response function, which is generally explained by the size of the electromechanical moment constant of the servo motor.

OTC welding robot as a widely used advanced automatic welding equipment, with high versatility, stable action characteristics, to use the robot to complete the welding task, the engineer only needs to teach the robot once can correctly reproduce the operation of the teaching process. Let the robot do the rest ...

Industrial robots refer to multi-joint manipulators or multi-degree-of-freedom robots for the industrial field. In addition to industrial robots, special robots are used in non-manufacturing industries and serve human beings, including: service robots, underwater robots, entertainment robots, military robots, ...

(1) Open and modular control architecture The distributed CPU computer structure is selected, which is divided into robot controller (RC), motion controller (MC), optoelectronic isolation I/O control board, sensor processing board and programming teaching box. Robot Controller (RC) & Programming ...

The robot vision system is generally composed of optical systems (light sources, lenses, industrial cameras), picture acquisition units, picture processing units, actuators and human-machine interfaces and other modules.