With the acquisition of more and more users of OTC robots, the popularity is growing. At present, more and more factory users have begun to pay attention to OTC robot products, and everyone may have a simple or in-depth understanding of OTC robot products from the Internet or related exhibitions.
On the Internet or in exhibitions, some OTC robot products that we can see are printed with the words DAIHEN instead of OTC, what is going on?
In fact, OTC is a title of Odichi in China, and in Japan, its title is DAIHEN.
Therefore, it is not enough to print the word DAIHEN on some OTC robot products.
However, in general, ODC robot products sold in Chinese mainland will only print the words OTC, not DAIHEN. So when we see an OTC robot product printed with the word DAIHEN, we can know that this is a product sold in other regions, or only in Japan.
Generally, we can find most of the robot products with the same OTC words as the DAIHEN product model, but those robot products that are special to certain areas cannot be found in the local ODC branch!
In addition, OTC robots are not called OTC in Taiwan, China, but TEC. These companies with different names are in fact selling products from the same company!
|
More on that
|
Welding robot wire feeder type - OD robot
1. The wire feeder is divided into two types: integrated and separated. The wire feeder is installed on the rear of the upper arm of the robot and is integrated with the robot; The wire feeder and the robot are separated from each other.
Because the distance from the integrated wire feeder to the welding gun is more than ...
|
|
Technical parameters of welding robot - OTC Odihi
1. Number of joints. The number of joints can also be referred to as degrees of freedom, which is an important indicator of the robot's flexibility. Generally speaking, the robot workspace can reach three degrees of freedom, but welding not only needs to reach a certain orientation in the space, but also needs to ensure the spatial posture of the welding gun.
...
|
|
Instructions for the common keys for the teach pendant – the Odish robot
1. The axis key that controls the movement of the junction is mainly used to adjust the orientation and angle of the robot and the welder. When the SW switch is pressed, the cooperative coordinates can be used to control the robot's orientation.
2. The coordinate switching button can be used to cut between axis coordinates, robot coordinates and tool coordinates.
|
|
Communication between welding robots and welding machines – OTC Odihi
Communication between the welding robot and the welding machine:
1. Analog communication
2. Digital Communications
Analog communication, generally directly connect the analog interface of the welding machine with the analog module of the robot (but also according to the requirements of the welding machine manufacturer, some welding machine analog communication needs to be added...
|
|
OTC Odichi welding machine replaces high-voltage electrolytic capacitors
The high-voltage electrolytic capacitor C2 supplies a stable DC to the primary inverter transformer to ensure the stable operation of the OTC welding machine. However, since the electrolytic capacitor is the same as the battery, the electrolyte is encapsulated inside, and the consumption of the electrolyte cannot be completely avoided, and its life span is limited.
Therefore, in order to ensure that the welding machine ...
|
|
OTC Odichi welding machine to reduce spatter method
Splash issues
Because metal is thrown from the weld point to adjacent surfaces, spatter reduces power and adds expense to the installation line. After the welding is completed, the welder needs to sort out the weld, and the rest of the data is wasted.
Many welders think it's part of welding. Many people learn ...
|
|
Advantages of ODS electric gripper over pneumatic gripper
In the field of industrial automation, grippers are a common and important tool. The role of the gripper is to clamp and fix objects, and are used for applications such as automatic installation, material handling and processing. And among the types of grippers, electric grippers and pneumatic grippers are two common picks. Well, the electric gripper ...
|
|
Robot interrupt function processing - OTC Odichi
Interruption means that in the process of computer operation, when there is some unexpected situation that requires the intervention of the host, the machine can automatically stop the running program and transfer to the program that deals with the new situation, and return to the original suspended program to continue to run after processing.
...
|
|
OTC Odchi welding robot programming steps
1. Find the operation origin of the OTC welding robot: click "Program" on the setting box, enter 9999, press "Confirm", press "Look Forward", and the yellow displayed on the setting box is the current process.
2. Create an empty ...
|
|
OTC welding robot programming steps
Step 1: Find an operation origin for the OTC welding robot: click "Program" on the teaching box, enter 9999, press "Confirm", press "Walk to View", and the yellow pole on the teaching box is displayed at that time.
Step 2: Create ...
|
|
Advantages of OTC robot synchronous feeding welding system
The primary advantages of the OTC robot synchronous feeding welding system:
1. The OTC robot synchronous feeding welding system has the ability to complete the ultra-high-speed control wire feeding, and the welding ability of the OTC Welbee welding used is also directly ...
|
|
Installation tutorial of OTC welding robot I/O board
The wiring method of the physical I/O signal line of the OTC welding robot relay equipment + I/O board is as follows:
1. Cut off the main power supply and circuit breaker on the control equipment.
2. Remove the back panel next to the control device.
...
|
|
The main classification of articulated robots - OTC Odichi
Articulated robots, also known as articulated robotic arms or multi-articulated robots, have the movement of each joint rolling, similar to a human arm. Articulated robots are one of the most common shapes of industrial robots in today's industrial sector, and are suitable for mechanical automation operations in many industrial fields.
...
|
|
Belt tension adjustment method and precautions - OTC robot
The OTC robot needs to adjust the tension of the belt once a year or every 3,000 hours of work, whichever is shorter. The OTC robot B4 (B4L) is used as an example to introduce the adjustment method and precautions.
The timing belt of the OTC robot B4\B4L is located in the motor and reduction gear.
|
|
The general trend of industrial robot technology development - Odixi
Industrial robot is a multi-joint manipulator or multi-degree of freedom intelligent machine device for the industrial category, which can perform work automatically, and is a kind of machine that relies on its own power and control ability to instigate various functions. Not only can it be commanded by humans, but it can also operate according to pre-programmed procedures.
|
|
Preparation of argon arc before welding
(1) Read the welding process diagram to understand the information, equipment, things and related process parameters of the workpiece to be welded, including the selection of the appropriate welding machine (such as the AC welding machine required for welding aluminum alloy), the selection of the appropriate tungsten electrode and gas flow. First of all, understand the welding current and ...
|
|
The relationship between ODS servos and robots
The servo motor is the driving device of the robot joint
The joint drive of the robot is inseparable from the servo system, and the more joints, the higher the flexibility and accuracy of the robot, and the more servo motors need to be used. The servo motor affects the robot's arm control, such as orientation, angle, etc.
|
|
OTC Odichi seven-axis industrial robot
OTC seven-axis industrial robot
Japan's DAIHEN Group Odihi has launched the latest seven-axis robots (FD-B4S, FD-B4LS, FD-V6S, FD-V6LS, FD-V20S). Thanks to the rotation of the seventh axis, they are able to complete tasks like ...
|
|
OTC welding robot nut welding false welding phenomenon processing
The general welding equipment is completely controlled by manual experience, so that the solder joints of the nut are high and low, and the output and power stability of the equipment are not ambitious, and the false welding phenomenon simply occurs. When welding nuts with general welding equipment, it is very simple to ...
|
|
Comparison of the advantages of the special sensor for arc welding of OTC welding robots!!
Welding robots are divided into arc welding robots and spot welding robots. Arc welding robots can be used for all arc welding, cutting techniques, and similar industrial methods. The commonly used range is self-consumable electrode active gas shielded welding (CO2 welding, MAG welding) of structural steel and chromium-nickel steel, metal welding of aluminum and special alloys.
|
|
Contact
working hours
