On December 10th, the "2020 Buke - IoT Machine Internet of Things Solution Seminar" was held in Wenzhou Ruian, with more than 60 company leaders including Tang Dong, chairman of Buke Co., Ltd., Wang Gang, sales executive, and Ouyang Yunsheng, director of HMI products, attended by more than 60 company leaders, as well as new/old agents and terminals from Wenzhou.

Buke touch screen in the industrial field, touch screen in China's market share has been ahead of the world's peers, in the forefront, while leading China's industrial touch screen skills to the direction of embedded and open development, Profibus, Canopen, Ethernet and other fieldbus skills integrated in our ...

Common models of Buke inverters 　　Buke CV100 series mini inverter The output frequency is 0-300Hz The carrier frequency is up to 15kHz, which effectively reduces the noise of the inverter It is equipped with RS-485 communication port as standard and supports Modbus communication protocol Sleep/wake function, inner ...

Common problems of Buke servo motors Why does the Kinco servo always display "Encoder counting" fault alarm? The first thing to check is: Whether the encoder cable is connected correctly. Whether the encoder cable is threaded with the motor cable or other AC cables...

A stepper motor driver is an actuator that converts electrical impulses into angular displacement. When the stepper driver receives a pulse signal, it drives the stepper motor to roll a fixed viewpoint (called the "step angle") in the set direction.

Buke touch screen programming software is a professional touch screen programming software, support for MT505T, MT506MV, MT508T, MT510T and other models, can assist users in the extreme time to grasp its planning methods, very suitable for modern industry increasingly large workload and function ...

1. According to the type of working power supply: it can be divided into DC motor and AC motor. 1) DC motors can be divided into brushless DC motors and brushed DC motors according to their structure and working principle. Brushed DC motors can be divided into: permanent magnet DC motors and electromagnetic DC motors.

Motor FAQs Generator overheating: If the stator voltage is too high, the iron loss will increase; The load current is too large and the power factor is too low, which increases the excitation current of the rotor and causes the motor to heat up; The three-phase load current of the generator is unbalanced: If the three-phase is unbalanced, it may cause the motor speed to be unbalanced.

1. Clean the motor and remove the dust and sludge outside the motor base in time. If there is a lot of dust in the environment, it is best to clean it once a day. 2. Check and wipe the motor terminals. Check whether the junction box wiring screws are loose or burned. 3. Check the screws of each fixing part, ...

1. For new or long-term out-of-service motors, the insulation resistance between the windings and the windings to the ground should be checked before use. Usually for motors below 500V, 500V insulation resistance meter is used; 1000V insulation resistance meter for 500-1000V motors; 2500V insulation resistance meter for motors above 1000V. Insulated ...

Material metering The measurement of powdery materials is commonly used in the way of screw measurement. The purpose of measurement is achieved by the number of turns of the screw rotation. In order to improve the accuracy of measurement, the speed of the screw is required to be adjustable, and the position positioning is accurate.

The stepper motor is a discrete motion device, which is intrinsically related to modern digital control technology. In the domestic digital control system, the stepper motor is widely used. With the advent of all-digital AC servo systems, AC servo motors are also increasingly used in digital ...

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

1. If the servo motor is an AC motor, it is a DC inverter air conditioner for speed regulation; If the servo motor is a DC brushless DC motor, it is the DC power supply DC transformer speed regulation; All servo motors can be used as "PLC motor speed regulating power supply circuit servo motor". 2、 ...

Recently, the Ministry of Industry and Information Technology of the People's Republic of China has completed the review of the fourth batch of specialized, special and new "little giant" enterprise cultivation, and publicized the list of enterprises that have passed the review.

1. The power of the motor 2. The power supply voltage of the motor 3. The encoder type of the motor 4. The size of the base of the motor 5. The movement mode of the motor 6. Motor communication bus 7. Whether the motor is equipped with a brake mechanism 8. Motor driver class ...

1. Encoder connection line failure: This kind of failure has the highest probability and is often encountered in maintenance, so it should be a priority factor. Often, encoder cables are open, short, or in poor contact, so the cable or connector needs to be replaced. Special attention should also be paid to whether the cable is loose and causes open soldering or ...

There are two main control methods of DC servo motor: one is armature voltage control, that is, under the condition that the stator magnetic field remains unchanged, the speed and output torque of the motor are controlled by controlling the voltage signals applied to both ends of the armature winding; The other is the excitation field control, that is, by changing the ...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...