Buke set off a new frenzy of "M-IoT machine Internet of Things".

1. Install the rotating shaft on the equipment casing, and the spindle and the equipment casing are supported by bearings. 2. Install the stator on the stop of the equipment housing and press it with the stator pressure ring. 3. Put the rotor into the inner hole of the stator, pay attention to protect the stator at the same time, and use the connecting bolt to connect the rotor with the ...

1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause a catastrophic failure of the bearing and the Buke motor to stop running. 2、 ...

1. In the daily inspection, the lubrication system, appearance, temperature, noise, vibration and abnormal phenomena are mainly checked, and the ventilation and cooling system, sliding friction and fastening of each component are also checked, and the inspection records are carefully made. 2. During the monthly or regular inspection, the main inspection ...

1. The motor temperature is too high or the smoke is faulty Cause: 1. Excessive load 2. Two-phase operation 3. Air duct blockage 4. The ambient temperature increases 5. Stator windings are short-circuited between phases or turns 6. Stator winding grounding 7. The power supply voltage is too high ...

1. a frame The frame structure varies depending on the motor cooling method, protection type, installation method, and purpose. According to its material classification, there are several types of cast iron, cast aluminum and steel plate structures. Cast iron frame with ribs. The base is connected to the end cap and fastened with bolts. Cast aluminum machine base generally does not have ...

1. High efficiency Due to its unique speed-torque capability, AC motors offer the highest efficiency for many applications, which allows them to run a wide range of applications while minimizing heat, wear, or degradation. Therefore, AC motors are often used to form large ...

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

1. Fault code: E-01, E-02 Significance: The parameters are initialized incorrectly during power-on. Cause: Incorrect parameter settings. Solution: Power back on, if the fault is still reported, you need to force the parameter initialization, if it is repeated many times, it cannot be solved.

1. Check whether the power supply voltage is stable and whether the logic voltage is within the input range of the driver, and use a separate power supply to supply power to the logic circuit; 2. The target current limit is set too small, and the current limit is increased within the allowable range. If you still can't find the reason for the above solutions, please ...

The main components of the motor include: 1. a frame; 2. an iron core; 3. a winding; 4. an end cover; 5. a bearing; 6. Centrifugal switch or starting relay and PTC starter; 7. a nameplate. 1 frame The frame structure varies depending on the cooling method, protection type, installation method and purpose of the motor.

Human-computer interaction refers to the interaction between humans and machines, which is essentially the interaction between humans and computers. Or more broadly: human-computer interaction refers to the interaction between a human and a machine containing a computer. Specifically, the two-way communication between the human-computer interaction user and the machine containing the computer ...

A servo motor encoder failure means that the encoder component is faulty, preventing it from generating and outputting the correct waveform. In this case, the method of repair is to replace the encoder or repair its internal parts. 1. Encoder connection line failure: this kind of failure has the highest probability of repair...

1. Calculate the load inertia and the matching of inertia, and the inertia matching of some products can reach 50 times, but in fact, the smaller the better, so that the accuracy and response speed are good. 2. Conversion of load torque on motor shaft and calculation of acceleration and deceleration torque. 3. Rotation speed and encoder resolution ...

1. Encoder connection line failure: This kind of failure has the highest probability and is often encountered in maintenance, so it should be a priority factor. Often, encoder cables are open, short, or in poor contact, so the cable or connector needs to be replaced. Special attention should also be paid to whether the cable is loose and causes open soldering or ...

1. Check the servo motor to ensure that there is no fatal damage outside; 2. Check the fixed parts of the servo motor to ensure that the connection is strong; 3. Check the output shaft of the servo motor to ensure the rotation and circulation; 4. Check the encoder connection line of the servo motor and the ...

(1) Encoder failure: It refers to the failure of the components of the encoder itself, resulting in its inability to generate and output correct waveforms. In this case, the encoder needs to be replaced or its internal components repaired. (2) Encoder connection cable failure: the probability of this fault is the highest, and the maintenance ...

1. Surface acoustic touch screen. (1) Fault 1: Touch deviation Symptom 1: The position of the finger does not coincide with the mouse arrow. Reason 1: After installing the driver, there is no vertical touch of the bullseye center position when the position is corrected. Solution 1: Recalibrate ...

The ordinary motors, stepper motors, servo motors, and servos mentioned here refer to DC micro motors, and most of the DC motors we usually come into contact with. An electric motor, also known as a "motor", refers to an electromagnetic induction device that maintains the transformation or transmission of electromagnetic energy according to the laws of electromagnetic induction. Motor...

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

1. Hydraulic servo control system The hydraulic servo control system is based on the power provided by the motor, and the hydraulic pump is used to convert the mechanical energy into pressure and push the hydraulic oil. By controlling various valves to change the flow direction of the hydraulic oil, so as to push the hydraulic cylinder to make different strokes, different directions of the movement...