Buke servo motor - AC servo motor maintenance method

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

The ordinary motors, stepper motors, servo motors, and servos mentioned here refer to DC micro motors, and most of the DC motors we usually come into contact with. An electric motor, also known as a "motor", refers to an electromagnetic induction device that maintains the transformation or transmission of electromagnetic energy according to the laws of electromagnetic induction. Motor...

1. Touch screen maintenance, touch no response fault phenomenon: When touching the screen, the mouse arrows do not move, and the position does not change. Second, the cause of the failure of touch screen maintenance touch non-response: (1) On the surface of the acoustic wave touch screen, the sound wave reflection stripes on the four perimeters ...

The servo motor can control the speed, the position accuracy is very accurate, and the voltage signal can be converted into torque and speed to drive the control object. The rotor speed of the servo motor is controlled by the input signal, and can respond quickly, in the automatic control system, used as an actuator, and has an electromechanical time constant...

1. When the motor rotates, the LED light flashes (1) Cause of failure: HALL phase error. Solution: Check whether the motor phase setting switch is correct (2) Fault cause: HALL sensor failure, treatment method: When the motor rotates, detect the voltage of HalA, HalB, HalC ...

Buke touch screen in the industrial field, touch screen in China's market share has been ahead of the world's peers, in the forefront, while leading China's industrial touch screen skills to the direction of embedded and open development, Profibus, Canopen, Ethernet and other fieldbus skills integrated in our ...

1. Change the rotational speed by changing the frequency of the mains supply This is a common method of speed adjustment for AC motors. The power supply frequency can be adjusted to the desired speed by adjusting the inverter, transformer, and other equipment. 2. Change the rotational speed by changing the voltage In some special cases ...

1. Servo motor pulse control mode In some small stand-alone equipment, the use of pulse control to achieve the positioning of the motor should be the most common application method, this control method is simple and easy to understand. The basic control idea: the total pulse amount determines the motor displacement, and the pulse frequency determines the ...

(1) Azimuth share gain Sets the share gain of the azimuth ring adjuster. The higher the set value, the higher the gain, the greater the stiffness, and the smaller the azimuth lag under the same frequency command pulse. However, too large a value may cause vibration or overshoot. The parameter values are determined by the detailed servo ...

1. For new or long-term out-of-service motors, the insulation resistance between the windings and the windings to the ground should be checked before use. Usually for motors below 500V, 500V insulation resistance meter is used; 1000V insulation resistance meter for 500-1000V motors; 2500V insulation resistance meter for motors above 1000V. Insulated ...

1. High efficiency Due to its unique speed-torque capability, AC motors offer the highest efficiency for many applications, which allows them to run a wide range of applications while minimizing heat, wear, or degradation. Therefore, AC motors are often used to form large ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

1. Hydraulic servo control system The hydraulic servo control system is based on the power provided by the motor, and the hydraulic pump is used to convert the mechanical energy into pressure and push the hydraulic oil. By controlling various valves to change the flow direction of the hydraulic oil, so as to push the hydraulic cylinder to make different strokes, different directions of the movement...

1. Check the servo motor to ensure that there is no fatal damage outside; 2. Check the fixed parts of the servo motor to ensure that the connection is strong; 3. Check the output shaft of the servo motor to ensure the rotation and circulation; 4. Check the encoder connection line of the servo motor and the ...

6. The motor vibrates greatly during operation (1) The cause of the failure (1) Due to excessive clearance of worn bearings; (2) uneven air gap; (3) Rotor imbalance; (4) Bending of the rotating shaft; (5) The coaxial axis of the coupling (pulley) is too low. (2) Troubleshooting ...

1. a frame The frame structure varies depending on the motor cooling method, protection type, installation method, and purpose. According to its material classification, there are several types of cast iron, cast aluminum and steel plate structures. Cast iron frame with ribs. The base is connected to the end cap and fastened with bolts. Cast aluminum machine base generally does not have ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke (1) The cause of the failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring error of the control equipment ...

Common problems of Buke servo motors Why does the Kinco servo always display "Encoder counting" fault alarm? The first thing to check is: Whether the encoder cable is connected correctly. Whether the encoder cable is threaded with the motor cable or other AC cables...

Drive Alarm 0006 Please troubleshoot in the following order: 1. Is the motor model correctly configured? 2. Is the motor encoder cable firmly connected? 3. If the above two points are correct, please replace the motor or driver for cross-comparison and troubleshooting. As mentioned above ...