Buke servo motor - what are the speed regulation methods of servo motor?

1. OC output: It is commonly said that the triode output, and the input impedance and circuit circuit need to be considered for connection. 2. Voltage output: In fact, it is also a format of OC output, but it has a built-in active circuit. 3. Push-pull output: the interface is easy to connect, no need to consider NPN and PN ...

1. Initialize parameters Before wiring, initialize the parameters. On the control card: Select the controller Style; Reset the PID parameter to zero; When the controller card is powered on, the enable signal is turned off by default, and this state is saved to ensure that the controller card is powered on again and the time force is in this state. Serving ...

Recently, the Ministry of Industry and Information Technology of the People's Republic of China has completed the review of the fourth batch of specialized, special and new "little giant" enterprise cultivation, and publicized the list of enterprises that have passed the review.

1. Wipe the motor. Remove the dust and sludge on the outside of the motor base in time. If there is a lot of dust in the environment, it is best to clean it once a day. 2. Check and wipe the motor terminals. Check whether the junction box wiring screws are loose or burned. 3. Check the screws of each fixed part ...

(1) Azimuth share gain Sets the share gain of the azimuth ring adjuster. The higher the set value, the higher the gain, the greater the stiffness, and the smaller the azimuth lag under the same frequency command pulse. However, too large a value may cause vibration or overshoot. The parameter values are determined by the detailed servo ...

1. How to deal with the servo motor not running when there is pulse output? a. Monitor the current value of the pulse output of the controller and whether the pulse output light is flashing, and confirm that the command pulse has been executed and the pulse has been output normally; b. Check the control cable from the controller to the driver, ...

1. Calculate the load inertia and the matching of inertia, and the inertia matching of some products can reach 50 times, but in fact, the smaller the better, so that the accuracy and response speed are good. 2. Conversion of load torque on motor shaft and calculation of acceleration and deceleration torque. 3. Rotation speed and encoder resolution ...

1. Install the rotating shaft on the equipment casing, and the spindle and the equipment casing are supported by bearings. 2. Install the stator on the stop of the equipment housing and press it with the stator pressure ring. 3. Put the rotor into the inner hole of the stator, pay attention to protect the stator at the same time, and use the connecting bolt to connect the rotor with the ...

A servo motor encoder failure means that the encoder component is faulty, preventing it from generating and outputting the correct waveform. In this case, the method of repair is to replace the encoder or repair its internal parts. 1. Encoder connection line failure: this kind of failure has the highest probability of repair...

Motor FAQs Generator overheating: If the stator voltage is too high, the iron loss will increase; The load current is too large and the power factor is too low, which increases the excitation current of the rotor and causes the motor to heat up; The three-phase load current of the generator is unbalanced: If the three-phase is unbalanced, it may cause the motor speed to be unbalanced.

1. Please check the motor power line to confirm whether there is a short circuit in the phase wire of the motor 2. If there is no short circuit in the phase line of the motor, it is determined that the internal power tube problem of the driver is determined

1. Sweeping: Sweeping is generally caused by friction of the stator and rotor due to bearing damage, shaft bending, or improper assembly during maintenance. In the process of overhaul and assembly of the motor, the parts of the motor should be kept clean, and the assembly of the end cover, bearing, etc. should be reasonable and not barbaric construction, otherwise ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke (1) The cause of the failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring error of the control equipment ...

1. Wide range of speed regulation 2. High positioning accuracy 3. There is sufficient transmission rigidity and high speed stability 4. Fast response, no overshoot In order to ensure productivity and processing quality, in addition to high positioning accuracy, it is also required to have a good and fast response ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

On December 17, Buke Co., Ltd. and Willis Towers Watson (formerly Torrei Watson, the world's leading professional services company) held the "Buke Co., Ltd. Organizational Reform and Upgrade Project Kick-off Meeting". Xu Changliang, Chief Consultant of Willis Towers Watson, Sheng Shaoqin, Partner of Willis Towers Watson, Tang Dong, Chairman of Buke Group, Bu...

1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause a catastrophic failure of the bearing and the Buke motor to stop running. 2、 ...

1. Touch screen maintenance, touch no response fault phenomenon: When touching the screen, the mouse arrows do not move, and the position does not change. Second, the cause of the failure of touch screen maintenance touch non-response: (1) On the surface of the acoustic wave touch screen, the sound wave reflection stripes on the four perimeters ...

Human-machine interface refers to the field where man and machine contact or interact with each other in information exchange and function, which facilitates our lives, but it is inevitable that there will be some failures when using human-machine interface machines, and how should we deal with these failures. First, the human-machine interface is normal but the computer is not...

1. High efficiency Due to its unique speed-torque capability, AC motors offer the highest efficiency for many applications, which allows them to run a wide range of applications while minimizing heat, wear, or degradation. Therefore, AC motors are often used to form large ...