Human-computer interaction refers to the interaction between humans and machines, which is essentially the interaction between humans and computers. Or more broadly: human-computer interaction refers to the interaction between a human and a machine containing a computer. Specifically, the two-way communication between the human-computer interaction user and the machine containing the computer ...

1. Install the rotating shaft on the equipment casing, and the spindle and the equipment casing are supported by bearings. 2. Install the stator on the stop of the equipment housing and press it with the stator pressure ring. 3. Put the rotor into the inner hole of the stator, pay attention to protect the stator at the same time, and use the connecting bolt to connect the rotor with the ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...

· They offer significant cost-effectiveness · They provide smoother operation · they are very efficient and tend to reduce energy costs · can optimize thermal management by embedding the motor into the machine · They offer improved servo performance and therefore improved production ...

Frameless torque motor is a new type of direct-drive torque motor, which is designed for applications that require small size, light weight, low inertia, low cogging torque, and high power. High reliability - no mechanical transmission, long life and easy installation. Serialized products are not limited to the following types ...

1. First of all, the first step is to power the 24V power supply: brown positive blue negative yellow and green wire. 2. Then it is necessary to connect the two sets of wires of the motor to the A+ A-, B+ B- of the driver. 3. Then connect the 24v power supply-v to the GND of the driver. 4. And then ...

1. Fault code: E-01, E-02 Significance: The parameters are initialized incorrectly during power-on. Cause: Incorrect parameter settings. Solution: Power back on, if the fault is still reported, you need to force the parameter initialization, if it is repeated many times, it cannot be solved.

Drive Alarm 0006 Please troubleshoot in the following order: 1. Is the motor model correctly configured? 2. Is the motor encoder cable firmly connected? 3. If the above two points are correct, please replace the motor or driver for cross-comparison and troubleshooting. As mentioned above ...

First, the common causes of such faults caused by mechanical oscillation (acceleration/deceleration) when the motor is powered on are: (1) The pulse encoder is faulty. At this time, the servo system should be checked to see if it is stable, whether the circuit board maintenance detection current is stable, and at the same time, the electrical ...

1. Check whether the power supply voltage is stable and whether the logic voltage is within the input range of the driver, and use a separate power supply to supply power to the logic circuit; 2. The target current limit is set too small, and the current limit is increased within the allowable range. If you still can't find the reason for the above solutions, please ...

1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause a catastrophic failure of the bearing and the Buke motor to stop running. 2、 ...

1. How to deal with the servo motor not running when there is pulse output? a. Monitor the current value of the pulse output of the controller and whether the pulse output light is flashing, and confirm that the command pulse has been executed and the pulse has been output normally; b. Check the control cable from the controller to the driver, ...

1. Servo motor pulse control mode In some small stand-alone equipment, the use of pulse control to achieve the positioning of the motor should be the most common application method, this control method is simple and easy to understand. The basic control idea: the total pulse amount determines the motor displacement, and the pulse frequency determines the ...

1. The servo mechanism is an automatic control system that enables the position, orientation, state and other output controlled quantities of the object to follow the arbitrary change of the input target (or given value). The servo mainly relies on the pulse to position, which can basically be understood in this way, the servo motor receives 1 ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

1. Remove the damaged encoder 2. Install a new encoder on the damaged motor 3. Find the Z signal and two power cords according to the figure, the general power supply is 5V. 4. Prepare a 24V and 5V output switching power supply with a slightly modified open circuit alarm and ...

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

One. SERVO MOTOR DIMENSIONS: 38MM, 58MM, 66MM, 80MM.100MM. Two. Servo motor encoders are divided into: singleturn, multiturn. Three. Servo motor encoders are divided into magnetic absolute encoders and photoelectric absolute encoders according to the principle Four. Servo motor ...

(1) Encoder failure: It refers to the failure of the components of the encoder itself, resulting in its inability to generate and output correct waveforms. In this case, the encoder needs to be replaced or its internal components repaired. (2) Encoder connection cable failure: the probability of this fault is the highest, and the maintenance ...

1. OC output: It is commonly said that the triode output, and the input impedance and circuit circuit need to be considered for connection. 2. Voltage output: In fact, it is also a format of OC output, but it has a built-in active circuit. 3. Push-pull output: the interface is easy to connect, no need to consider NPN and PN ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...