Buke servo motor - what are the basic applications of AC servo motor?

Recently, the Ministry of Industry and Information Technology of the People's Republic of China has completed the review of the fourth batch of specialized, special and new "little giant" enterprise cultivation, and publicized the list of enterprises that have passed the review.

B3: The base has feet. The end cap has no flange. Mounted on foundation members. B35: The frame has feet. Flange on the end cap. The flange has through holes. It is installed on the foundation member by a foot and attached to the flange mounting. B34: The frame has feet. The end cap has a flange and a screw on the flange.

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

Hmi: Human-machine interface refers to the field in which man and machine contact or interact with each other in information exchange and function, or the human-machine interface mentioned in the interface. Information exchange, functional contact or mutual influence, refers to the hard contact and soft contact between man and machine, this combination includes not only dots and lines...

Fiber laser cutting machine has been widely accepted by the society and used in many industries, welcomed by customers, helping customers improve production efficiency and improve product competitiveness. But at the same time, we don't know much about the functions of the machine components, so today we will talk about fiber lasers.

1. Adopt a power supply with excellent performance to suppress the interference introduced by the power grid. For the power supply supplied by the PLC controller, the non-power line power supply should be adopted, and the special line power supply should be used directly from the main bus of the low-voltage distribution room. Isolation transformers are selected, and the transformer capacity should be larger than the actual needs.

Motor FAQs Generator overheating: If the stator voltage is too high, the iron loss will increase; The load current is too large and the power factor is too low, which increases the excitation current of the rotor and causes the motor to heat up; The three-phase load current of the generator is unbalanced: If the three-phase is unbalanced, it may cause the motor speed to be unbalanced.

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

1. The indicated value is large (or out of range). According to the investigation of our staff, this kind of problem often appears in the atmospheric pressure workshop. When we find that the counterweight of the float in the float level gauge is at a low point, the liquid level must be very high at this time, and the glass plate is inconsistent with the indication of the instrument.

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

1. Please check the motor power line to confirm whether there is a short circuit in the phase wire of the motor 2. If there is no short circuit in the phase line of the motor, it is determined that the internal power tube problem of the driver is determined

1. First of all, the first step is to power the 24V power supply: brown positive blue negative yellow and green wire. 2. Then it is necessary to connect the two sets of wires of the motor to the A+ A-, B+ B- of the driver. 3. Then connect the 24v power supply-v to the GND of the driver. 4. And then ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

AC motor speed regulation is achieved by changing the electrical parameters such as the power supply frequency, number of pole pairs and slip rate of AC motor. 1. Use the inverter to change the power supply frequency speed regulation, the speed regulation range is large, the stability and smoothness are good, and the mechanical characteristics are hard. It's just to add the amount ...

What are the power requirements for hardware setup 1, ED100 and ED200? The logic power supply of the Kinco servo is DC24V (scale is 18V-30V), not less than 1A (if the boundary says OUT and Brake output, it is not less than 2A); The power supply of ED100 is DC24V-DC70V, and the power supply requirements of ED200 and ED216 are D...

The main components of the motor include: 1. a frame; 2. an iron core; 3. a winding; 4. an end cover; 5. a bearing; 6. Centrifugal switch or starting relay and PTC starter; 7. a nameplate. 1 frame The frame structure varies depending on the cooling method, protection type, installation method and purpose of the motor.

1. The working principle of servo motor encoder It is a rotary sensor that converts rotational displacement into a series of digital pulse signals that can be used to control angular displacement, and can also be used to measure linear displacement if the encoder is combined with a gear bar or spiral screw. ...

1. OC output: It is commonly said that the triode output, and the input impedance and circuit circuit need to be considered for connection. 2. Voltage output: In fact, it is also a format of OC output, but it has a built-in active circuit. 3. Push-pull output: the interface is easy to connect, no need to consider NPN and PN ...

1. The power of the motor 2. The power supply voltage of the motor 3. The encoder type of the motor 4. The size of the base of the motor 5. The movement mode of the motor 6. Motor communication bus 7. Whether the motor is equipped with a brake mechanism 8. Motor driver class ...

On December 17, Buke Co., Ltd. and Willis Towers Watson (formerly Torrei Watson, the world's leading professional services company) held the "Buke Co., Ltd. Organizational Reform and Upgrade Project Kick-off Meeting". Xu Changliang, Chief Consultant of Willis Towers Watson, Sheng Shaoqin, Partner of Willis Towers Watson, Tang Dong, Chairman of Buke Group, Bu...