Buke touch screen profile and model

Point 1 When the servo motor jitters at zero speed, the gain should be set high, which can reduce the gain value. If the alarm stops when starting, the most likely is that the phase sequence of the motor is incorrect. Point 2 1. When the PID gain adjustment is too large, it is easy to induce...

What are the power requirements for hardware setup 1, ED100 and ED200? The logic power supply of the Kinco servo is DC24V (scale is 18V-30V), not less than 1A (if the boundary says OUT and Brake output, it is not less than 2A); The power supply of ED100 is DC24V-DC70V, and the power supply requirements of ED200 and ED216 are D...

(1) Azimuth share gain Sets the share gain of the azimuth ring adjuster. The higher the set value, the higher the gain, the greater the stiffness, and the smaller the azimuth lag under the same frequency command pulse. However, too large a value may cause vibration or overshoot. The parameter values are determined by the detailed servo ...

1. Comparison link The comparison link is to compare the input command signal with the feedback signal of the system to obtain the deviation signal between the output and the input, which is usually implemented by a special circuit or computer. 2. a controller The controller is usually a computer or PI...

The main components of the motor include: 1. a frame; 2. an iron core; 3. a winding; 4. an end cover; 5. a bearing; 6. Centrifugal switch or starting relay and PTC starter; 7. a nameplate. 1 frame The frame structure varies depending on the cooling method, protection type, installation method and purpose of the motor.

Advantages and disadvantages of DC servo motors Advantages: accurate speed control, torque speed characteristics are very hard, simple control principle, easy to use, cheap price. Disadvantages: brush commutation, speed limit, additional resistance, occurrence of wear particles (not suitable for dust-free and explosive environments). Straight...

1. Remove the damaged encoder 2. Install a new encoder on the damaged motor 3. Find the Z signal and two power cords according to the figure, the general power supply is 5V. 4. Prepare a 24V and 5V output switching power supply with a slightly modified open circuit alarm and ...

(1) Accurate detection device: to form a closed-loop control of speed and position. (2) There are a variety of feedback comparison principles and methods: according to the principle of information feedback realized by the detection device, the feedback comparison method of the servo system is also different. At present, the commonly used pulse comparison, phase ratio ...

Buke touch screen programming software is a professional touch screen programming software, support for MT505T, MT506MV, MT508T, MT510T and other models, can assist users in the extreme time to grasp its planning methods, very suitable for modern industry increasingly large workload and function ...

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke (1) The cause of the failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring error of the control equipment ...

Common problems of Buke servo motors Why does the Kinco servo always display "Encoder counting" fault alarm? The first thing to check is: Whether the encoder cable is connected correctly. Whether the encoder cable is threaded with the motor cable or other AC cables...

1. Surface acoustic touch screen. (1) Fault 1: Touch deviation Symptom 1: The position of the finger does not coincide with the mouse arrow. Reason 1: After installing the driver, there is no vertical touch of the bullseye center position when the position is corrected. Solution 1: Recalibrate ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

Since the new crown epidemic, the rapid growth of e-commerce has made the overall scale of China's express delivery industry grow rapidly, according to incomplete statistics, the business volume in 2020 has exceeded 80 billion pieces. Due to the growth of express delivery business volume, the automatic sorting efficiency of express delivery and parcels is becoming higher and higher.

1. Start the servo motor before work (1) Measure the insulation resistance (0.5M or more for low-voltage motors). (2) Measure the power supply voltage, check whether the wiring of the motor is correct, and whether the power supply voltage meets the requirements. (3) Check whether the starting device is normal. ( ...

The ordinary motors, stepper motors, servo motors, and servos mentioned here refer to DC micro motors, and most of the DC motors we usually come into contact with. An electric motor, also known as a "motor", refers to an electromagnetic induction device that maintains the transformation or transmission of electromagnetic energy according to the laws of electromagnetic induction. Motor...

6. When the motor is unloaded and overloaded, the ammeter pointer is unstable and swings 1. Cause of failure (1) The cage rotor guide bar is welded or broken; (2) Winding rotor fault (one-phase break) or poor contact of brushes and collector ring short-circuit devices. 2. Troubleshooting ...

1. The motor temperature is too high or the smoke is faulty Cause: 1. Excessive load 2. Two-phase operation 3. Air duct blockage 4. The ambient temperature increases 5. Stator windings are short-circuited between phases or turns 6. Stator winding grounding 7. The power supply voltage is too high ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...