Buke servo motor - the division of the motor and its detailed introduction

1. For new or long-term out-of-service motors, the insulation resistance between the windings and the windings to the ground should be checked before use. Usually for motors below 500V, 500V insulation resistance meter is used; 1000V insulation resistance meter for 500-1000V motors; 2500V insulation resistance meter for motors above 1000V. Insulated ...

1. Fault code: E-01, E-02 Significance: The parameters are initialized incorrectly during power-on. Cause: Incorrect parameter settings. Solution: Power back on, if the fault is still reported, you need to force the parameter initialization, if it is repeated many times, it cannot be solved.

1. Initialize parameters Before wiring, initialize the parameters. On the control card: Select the controller Style; Reset the PID parameter to zero; When the controller card is powered on, the enable signal is turned off by default, and this state is saved to ensure that the controller card is powered on again and the time force is in this state. Serving ...

The first type, the split-phase starting type, as shown in Figure 1, is assisted by an auxiliary starting winding, and its starting torque is not large. The operating rate remains roughly constant. It is mainly used in electric fans, air conditioning fans, motors, washing machines and other motors. Second, when the motor is stationary, the centrifugal switch is connected to the ...

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

1. Wide range of speed regulation 2. High positioning accuracy 3. There is sufficient transmission rigidity and high speed stability 4. Fast response, no overshoot In order to ensure productivity and processing quality, in addition to high positioning accuracy, it is also required to have a good and fast response ...

The stepper motor is a discrete motion device, which is intrinsically related to modern digital control technology. In the domestic digital control system, the stepper motor is widely used. With the advent of all-digital AC servo systems, AC servo motors are also increasingly used in digital ...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

In the past industrial field, HMI touch screens were used more as a window for people to interact with mechanical equipment, and were used to connect various PLCs and sensors. Nowadays, in the context of the Industrial Internet of Things, manufacturing enterprises need to integrate OT and IT technologies more to achieve their own digital and intelligent transformation.

1. Adopt a power supply with excellent performance to suppress the interference introduced by the power grid. For the power supply supplied by the PLC controller, the non-power line power supply should be adopted, and the special line power supply should be used directly from the main bus of the low-voltage distribution room. Isolation transformers are selected, and the transformer capacity should be larger than the actual needs.

Common models of Buke inverters 　　Buke CV100 series mini inverter The output frequency is 0-300Hz The carrier frequency is up to 15kHz, which effectively reduces the noise of the inverter It is equipped with RS-485 communication port as standard and supports Modbus communication protocol Sleep/wake function, inner ...

1. Remove the damaged encoder 2. Install a new encoder on the damaged motor 3. Find the Z signal and two power cords according to the figure, the general power supply is 5V. 4. Prepare a 24V and 5V output switching power supply with a slightly modified open circuit alarm and ...

6. When the motor is unloaded and overloaded, the ammeter pointer is unstable and swings 1. Cause of failure (1) The cage rotor guide bar is welded or broken; (2) Winding rotor fault (one-phase break) or poor contact of brushes and collector ring short-circuit devices. 2. Troubleshooting ...

1. OC output: It is commonly said that the triode output, and the input impedance and circuit circuit need to be considered for connection. 2. Voltage output: In fact, it is also a format of OC output, but it has a built-in active circuit. 3. Push-pull output: the interface is easy to connect, no need to consider NPN and PN ...

1. Servo motor encoder is a product installed on the servo motor, which is equivalent to a sensor. 2. Do speed closed-loop and azimuth closed-loop to complete accurate speed regulation and accurate azimuth control. 3. The servo motor has its own encoder, which can be converted into servo electronic gears.

1. Check the servo motor to ensure that there is no fatal damage outside; 2. Check the fixed parts of the servo motor to ensure that the connection is strong; 3. Check the output shaft of the servo motor to ensure the rotation and circulation; 4. Check the encoder connection line of the servo motor and the ...

Buke touch screen in the industrial field, touch screen in China's market share has been ahead of the world's peers, in the forefront, while leading China's industrial touch screen skills to the direction of embedded and open development, Profibus, Canopen, Ethernet and other fieldbus skills integrated in our ...

1. First of all, the first step is to power the 24V power supply: brown positive blue negative yellow and green wire. 2. Then it is necessary to connect the two sets of wires of the motor to the A+ A-, B+ B- of the driver. 3. Then connect the 24v power supply-v to the GND of the driver. 4. And then ...

1. Change the rotational speed by changing the frequency of the mains supply This is a common method of speed adjustment for AC motors. The power supply frequency can be adjusted to the desired speed by adjusting the inverter, transformer, and other equipment. 2. Change the rotational speed by changing the voltage In some special cases ...