Buke servo motor - common faults and solutions of servo motor encoders

1. Change the rotational speed by changing the frequency of the mains supply This is a common method of speed adjustment for AC motors. The power supply frequency can be adjusted to the desired speed by adjusting the inverter, transformer, and other equipment. 2. Change the rotational speed by changing the voltage In some special cases ...

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...

1. In the daily inspection, the lubrication system, appearance, temperature, noise, vibration and abnormal phenomena are mainly checked, and the ventilation and cooling system, sliding friction and fastening of each component are also checked, and the inspection records are carefully made. 2. During the monthly or regular inspection, the main inspection ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke (1) The cause of the failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring error of the control equipment ...

Reasons for the shutdown of the speed up Buke motor due to contamination: 1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause the bearing and the ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...

1. OC output: It is commonly said that the triode output, and the input impedance and circuit circuit need to be considered for connection. 2. Voltage output: In fact, it is also a format of OC output, but it has a built-in active circuit. 3. Push-pull output: the interface is easy to connect, no need to consider NPN and PN ...

1. Initialize parameters Before wiring, initialize the parameters. On the control card: Select the controller Style; Reset the PID parameter to zero; When the controller card is powered on, the enable signal is turned off by default, and this state is saved to ensure that the controller card is powered on again and the time force is in this state. Serving ...

1. The motor temperature is too high or the smoke is faulty Cause: 1. Excessive load 2. Two-phase operation 3. Air duct blockage 4. The ambient temperature increases 5. Stator windings are short-circuited between phases or turns 6. Stator winding grounding 7. The power supply voltage is too high ...

1. Communication cannot be connected. 2. The interference in the process of data transmission will increase (sometimes it is not bad, but the connection between the host computer and the servo is incorrect, or there is a falling off, which is a very common problem). 3. The motor will run, but it will not work according to the instructions given by the servo ...

Human-machine interface refers to the field where man and machine contact or interact with each other in information exchange and function, which facilitates our lives, but it is inevitable that there will be some failures when using human-machine interface machines, and how should we deal with these failures. First, the human-machine interface is normal but the computer is not...

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke. 1. Cause of failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) Control ...

Buke touch screen in the industrial field, touch screen in China's market share has been ahead of the world's peers, in the forefront, while leading China's industrial touch screen skills to the direction of embedded and open development, Profibus, Canopen, Ethernet and other fieldbus skills integrated in our ...

On December 10th, the "2020 Buke - IoT Machine Internet of Things Solution Seminar" was held in Wenzhou Ruian, with more than 60 company leaders including Tang Dong, chairman of Buke Co., Ltd., Wang Gang, sales executive, and Ouyang Yunsheng, director of HMI products, attended by more than 60 company leaders, as well as new/old agents and terminals from Wenzhou.

Fiber laser cutting machine has been widely accepted by the society and used in many industries, welcomed by customers, helping customers improve production efficiency and improve product competitiveness. But at the same time, we don't know much about the functions of the machine components, so today we will talk about fiber lasers.

On December 7, Buke was invited to participate in the "2020 China Mobile Robot (AGV/AMR) Industry Development Annual Conference" hosted by the People's Government of Songjiang District, Shanghai and hosted by the China Mobile Robot (AGV) Industry Alliance. At the same time, Buke has also won the "Annual Quality Supply Chain Award" for three consecutive years.

On December 22, 2020, Buke Company held a 2021 marketing reform project promotion meeting with the theme of "Marketing Iron Army, Direct to Customers". At this conference, Buke invited Fan Houhua, the founder of Shenzhen Chuanshi Wisdom Technology Co., Ltd., and Yao Weixiang, senior consultant of Chuanshi Wisdom.

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

Drive Alarm 0006 Please troubleshoot in the following order: 1. Is the motor model correctly configured? 2. Is the motor encoder cable firmly connected? 3. If the above two points are correct, please replace the motor or driver for cross-comparison and troubleshooting. As mentioned above ...