Common models of Buke inverters

Material metering The measurement of powdery materials is commonly used in the way of screw measurement. The purpose of measurement is achieved by the number of turns of the screw rotation. In order to improve the accuracy of measurement, the speed of the screw is required to be adjustable, and the position positioning is accurate.

1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause a catastrophic failure of the bearing and the Buke motor to stop running. 2、 ...

A servo motor encoder failure means that the encoder component is faulty, preventing it from generating and outputting the correct waveform. In this case, the method of repair is to replace the encoder or repair its internal parts. 1. Encoder connection line failure: this kind of failure has the highest probability of repair...

1. First of all, the first step is to power the 24V power supply: brown positive blue negative yellow and green wire. 2. Then it is necessary to connect the two sets of wires of the motor to the A+ A-, B+ B- of the driver. 3. Then connect the 24v power supply-v to the GND of the driver. 4. And then ...

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...

Drive Alarm 0006 Please troubleshoot in the following order: 1. Is the motor model correctly configured? 2. Is the motor encoder cable firmly connected? 3. If the above two points are correct, please replace the motor or driver for cross-comparison and troubleshooting. As mentioned above ...

1. If the servo motor is an AC motor, it is a DC inverter air conditioner for speed regulation; If the servo motor is a DC brushless DC motor, it is the DC power supply DC transformer speed regulation; All servo motors can be used as "PLC motor speed regulating power supply circuit servo motor". 2、 ...

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

1. The servo mechanism is an automatic control system that enables the position, orientation, state and other output controlled quantities of the object to follow the arbitrary change of the input target (or given value). The servo mainly relies on the pulse to position, which can basically be understood in this way, the servo motor receives 1 ...

Buke touch screen in the industrial field, touch screen in China's market share has been ahead of the world's peers, in the forefront, while leading China's industrial touch screen skills to the direction of embedded and open development, Profibus, Canopen, Ethernet and other fieldbus skills integrated in our ...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

One. SERVO MOTOR DIMENSIONS: 38MM, 58MM, 66MM, 80MM.100MM. Two. Servo motor encoders are divided into: singleturn, multiturn. Three. Servo motor encoders are divided into magnetic absolute encoders and photoelectric absolute encoders according to the principle Four. Servo motor ...

1. How to deal with the servo motor not running when there is pulse output? a. Monitor the current value of the pulse output of the controller and whether the pulse output light is flashing, and confirm that the command pulse has been executed and the pulse has been output normally; b. Check the control cable from the controller to the driver, ...

Buke MK series all-in-one machine on the market for more than a year, received unanimous praise from many customers, in the Buke "quality first" to create an end-to-end full life cycle product quality management system" and "demand management" under the internal and external drive, through the application feedback of this series of products and in order to fit more ...

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...

In the past industrial field, HMI touch screens were used more as a window for people to interact with mechanical equipment, and were used to connect various PLCs and sensors. Nowadays, in the context of the Industrial Internet of Things, manufacturing enterprises need to integrate OT and IT technologies more to achieve their own digital and intelligent transformation.

Common problems of Buke servo motors Why does the Kinco servo always display "Encoder counting" fault alarm? The first thing to check is: Whether the encoder cable is connected correctly. Whether the encoder cable is threaded with the motor cable or other AC cables...

Reasons for the shutdown of the speed up Buke motor due to contamination: 1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause the bearing and the ...

What are the main differences between the two? 1. The way of control is different Stepper motor: The rotation angle is controlled by controlling the number of pulses, and one pulse corresponds to a step angle. Servo motor: The angle of rotation is controlled by controlling the length of the pulse time. 2. Work ...