Buke human-machine interface - the basic functions and selection indicators of human-machine interface products

1. Remove the motor encoder, power on the system, and power on the driver 2. Set the drive password to 510 and the No. 4 parameter to 4 (encoder zeroing mode) 3. Switch the driver to the encoder zero mode CO-press the confirm key to enter the CO-rdy ...

1. Encoder connection line failure: This kind of failure has the highest probability and is often encountered in maintenance, so it should be a priority factor. Often, encoder cables are open, short, or in poor contact, so the cable or connector needs to be replaced. Special attention should also be paid to whether the cable is loose and causes open soldering or ...

1. For new or long-term out-of-service motors, the insulation resistance between the windings and the windings to the ground should be checked before use. Usually for motors below 500V, 500V insulation resistance meter is used; 1000V insulation resistance meter for 500-1000V motors; 2500V insulation resistance meter for motors above 1000V. Insulated ...

1. The servo mechanism is an automatic control system that enables the position, orientation, state and other output controlled quantities of the object to follow the arbitrary change of the input target (or given value). The servo mainly relies on the pulse to position, which can basically be understood in this way, the servo motor receives 1 ...

The ordinary motors, stepper motors, servo motors, and servos mentioned here refer to DC micro motors, and most of the DC motors we usually come into contact with. An electric motor, also known as a "motor", refers to an electromagnetic induction device that maintains the transformation or transmission of electromagnetic energy according to the laws of electromagnetic induction. Motor...

1. The indicated value is large (or out of range). According to the investigation of our staff, this kind of problem often appears in the atmospheric pressure workshop. When we find that the counterweight of the float in the float level gauge is at a low point, the liquid level must be very high at this time, and the glass plate is inconsistent with the indication of the instrument.

Drive Alarm 0006 Please troubleshoot in the following order: 1. Is the motor model correctly configured? 2. Is the motor encoder cable firmly connected? 3. If the above two points are correct, please replace the motor or driver for cross-comparison and troubleshooting. As mentioned above ...

On December 17, Buke Co., Ltd. and Willis Towers Watson (formerly Torrei Watson, the world's leading professional services company) held the "Buke Co., Ltd. Organizational Reform and Upgrade Project Kick-off Meeting". Xu Changliang, Chief Consultant of Willis Towers Watson, Sheng Shaoqin, Partner of Willis Towers Watson, Tang Dong, Chairman of Buke Group, Bu...

Frameless torque motor is a new type of direct-drive torque motor, which is designed for applications that require small size, light weight, low inertia, low cogging torque, and high power. High reliability - no mechanical transmission, long life and easy installation. Serialized products are not limited to the following types ...

The main components of the motor include: 1. a frame; 2. an iron core; 3. a winding; 4. an end cover; 5. a bearing; 6. Centrifugal switch or starting relay and PTC starter; 7. a nameplate. 1 frame The frame structure varies depending on the cooling method, protection type, installation method and purpose of the motor.

A servo motor encoder failure means that the encoder component is faulty, preventing it from generating and outputting the correct waveform. In this case, the method of repair is to replace the encoder or repair its internal parts. 1. Encoder connection line failure: this kind of failure has the highest probability of repair...

Do not apply direct impact to the shaft during installation. The connection between the servo motor encoder shaft and the machine should use flexible connectors. When attaching connectors to the shaft, do not press them in. Even if a connector is used, it is possible to add a load greater than the allowable load to the shaft due to poor installation, ...

· They offer significant cost-effectiveness · They provide smoother operation · they are very efficient and tend to reduce energy costs · can optimize thermal management by embedding the motor into the machine · They offer improved servo performance and therefore improved production ...

1. How to deal with the servo motor not running when there is pulse output? a. Monitor the current value of the pulse output of the controller and whether the pulse output light is flashing, and confirm that the command pulse has been executed and the pulse has been output normally; b. Check the control cable from the controller to the driver, ...

Common models of Buke inverters 　　Buke CV100 series mini inverter The output frequency is 0-300Hz The carrier frequency is up to 15kHz, which effectively reduces the noise of the inverter It is equipped with RS-485 communication port as standard and supports Modbus communication protocol Sleep/wake function, inner ...

1. Clean the motor and remove the dust and sludge outside the motor base in time. If there is a lot of dust in the environment, it is best to clean it once a day. 2. Check and wipe the motor terminals. Check whether the junction box wiring screws are loose or burned. 3. Check the screws of each fixing part, ...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

1. Initialize parameters Before wiring, initialize the parameters. On the control card: Select the controller Style; Reset the PID parameter to zero; When the controller card is powered on, the enable signal is turned off by default, and this state is saved to ensure that the controller card is powered on again and the time force is in this state. Serving ...

1. Resistive touch screen The most important part of a resistive touchscreen is a resistive thin-film screen that matches the surface of the display very well. This is a multi-layer composite film based on a layer of glass or hard plastic plate, coated with a transparent metal oxide (ITO indium oxide, transparent conductive ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...