The main components of the motor include: 1. a frame; 2. an iron core; 3. a winding; 4. an end cover; 5. a bearing; 6. Centrifugal switch or starting relay and PTC starter; 7. a nameplate. 1 frame The frame structure varies depending on the cooling method, protection type, installation method and purpose of the motor.

1. High efficiency Due to its unique speed-torque capability, AC motors offer the highest efficiency for many applications, which allows them to run a wide range of applications while minimizing heat, wear, or degradation. Therefore, AC motors are often used to form large ...

1. Adopt a power supply with excellent performance to suppress the interference introduced by the power grid. For the power supply supplied by the PLC controller, the non-power line power supply should be adopted, and the special line power supply should be used directly from the main bus of the low-voltage distribution room. Isolation transformers are selected, and the transformer capacity should be larger than the actual needs.

1. The basic functions and selection indicators of human-machine interface products Basic Functions: Display of equipment working status, such as indicator lights, buttons, text, graphics, curves, etc.; Data and text input operations, printouts; Production recipe storage, equipment production data ...

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

Cause of the failure 1) The sound wave reflection stripes on the four periphery of the surface sound wave touch screen are seriously dusty or scale, resulting in the touch screen not working. 2) The touch screen is malfunctioning. 3) The touch screen control card is faulty. 4) The touch screen signal line is faulty ...

1. Calculate the load inertia and the matching of inertia, and the inertia matching of some products can reach 50 times, but in fact, the smaller the better, so that the accuracy and response speed are good. 2. Conversion of load torque on motor shaft and calculation of acceleration and deceleration torque. 3. Rotation speed and encoder resolution ...

Point 1 When the servo motor jitters at zero speed, the gain should be set high, which can reduce the gain value. If the alarm stops when starting, the most likely is that the phase sequence of the motor is incorrect. Point 2 1. When the PID gain adjustment is too large, it is easy to induce...

Fiber laser cutting machine has been widely accepted by the society and used in many industries, welcomed by customers, helping customers improve production efficiency and improve product competitiveness. But at the same time, we don't know much about the functions of the machine components, so today we will talk about fiber lasers.

1. Initialize parameters Before wiring, initialize the parameters. On the control card: Select the controller Style; Reset the PID parameter to zero; When the controller card is powered on, the enable signal is turned off by default, and this state is saved to ensure that the controller card is powered on again and the time force is in this state. Serving ...

What are the main differences between the two? 1. The way of control is different Stepper motor: The rotation angle is controlled by controlling the number of pulses, and one pulse corresponds to a step angle. Servo motor: The angle of rotation is controlled by controlling the length of the pulse time. 2. Work ...

The ordinary motors, stepper motors, servo motors, and servos mentioned here refer to DC micro motors, and most of the DC motors we usually come into contact with. An electric motor, also known as a "motor", refers to an electromagnetic induction device that maintains the transformation or transmission of electromagnetic energy according to the laws of electromagnetic induction. Motor...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

6. The motor vibrates greatly during operation (1) The cause of the failure (1) Due to excessive clearance of worn bearings; (2) uneven air gap; (3) Rotor imbalance; (4) Bending of the rotating shaft; (5) The coaxial axis of the coupling (pulley) is too low. (2) Troubleshooting ...

MT4000 series MT4000 series HMI is a sub-series of eView HMI, which is one of Buke's HMI products Series, human-machine interface MT4000 is referred to as ordinary application series. MT4000 series HMI products adopt 32 ...

Reasons for the shutdown of the speed up Buke motor due to contamination: 1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause the bearing and the ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke (1) The cause of the failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) The wiring error of the control equipment ...

1. The motor temperature is too high or the smoke is faulty Cause: 1. Excessive load 2. Two-phase operation 3. Air duct blockage 4. The ambient temperature increases 5. Stator windings are short-circuited between phases or turns 6. Stator winding grounding 7. The power supply voltage is too high ...

Due to the limitations of technology and environmental adaptability, the surface touch screen will not be able to be used normally due to water droplets, dust and other pollution not being treated in time, so the touch screen also needs regular maintenance like ordinary machines. And because the touch screen is a variety of electrical equipment high ...

Since the new crown epidemic, the rapid growth of e-commerce has made the overall scale of China's express delivery industry grow rapidly, according to incomplete statistics, the business volume in 2020 has exceeded 80 billion pieces. Due to the growth of express delivery business volume, the automatic sorting efficiency of express delivery and parcels is becoming higher and higher.