1. Errors in improper introduction of devices
In other words, the thermocouple should not be installed too close to the door and the heating place, and the penetration depth should be at least 8-10 times the diameter of the maintenance tube; The interval between the thermocouple maintenance sleeve and the wall is not filled with thermal insulation substances, resulting in heat overflow or cold air intrusion in the furnace, so the open space between the thermocouple maintenance pipe and the furnace wall hole is blocked with thermal insulation materials such as refractory mud or asbestos rope to avoid the convection of cold and hot air and affect the accuracy of temperature measurement; The cold end of the thermocouple is too close to the furnace body to exceed 100°C; The thermocouple device should avoid strong magnetic and electric fields as much as possible, so the thermocouple and the power cable should not be installed in the same conduit to avoid causing errors due to the introduction of disturbances; When measuring the temperature of the gas in the tube with a thermocouple, it is necessary to make the thermocouple device in the direction of the flow velocity and fully contact with the gas.
2. Errors introduced due to deterioration of insulation
If the thermocouple is insulated, the maintenance pipe and the cable plate have too much dirt or salt slag, resulting in poor insulation between the thermoelectric dipole and the furnace wall, which is more serious at high temperatures, which will not only cause the loss of thermoelectric potential but also introduce disturbance, and the resulting errors can sometimes reach hundreds.
3. Errors in the introduction of thermal inertia
This effect is particularly outstanding when performing rapid measurements, as the thermal inertness of the thermocouple causes the apparent value to lag behind the change in the measured temperature. Therefore, thermocouples with thinner thermoelectrodes and smaller diameter maintenance tubes should be used as much as possible. If the temperature measurement environment is agreed, the maintenance tube can even be removed. Because of the measurement hysteresis, the amplitude of the temperature fluctuation detected by the thermocouple is smaller than that of the furnace temperature fluctuation. The greater the measurement hysteresis, the smaller the amplitude of the thermocouple shaking and the greater the difference from the actual furnace temperature. When a thermocouple with a large time constant is used to measure or control the temperature, the temperature displayed on the surface fluctuates slightly, but the actual furnace temperature fluctuates greatly. In order to accurately measure the temperature, a thermal separation couple with a small time constant should be selected. The time constant is inversely proportional to the heat transfer coefficient, and is directly proportional to the diameter of the thermocouple hot end, the density of the data and the specific heat. In application, materials with good thermal conductivity and maintenance sleeves with thin walls and small inner diameters are usually selected. In more precise temperature measurement, bare wire thermocouples without maintenance sleeves are used, but the thermocouple is simply damaged and should be calibrated and replaced in time.
4. Thermal resistance error
At high temperatures, if there is a layer of coal ash on the maintenance pipe and dust adheres to it, the thermal resistance is added to prevent the conduction of heat, and the temperature indication is lower than the true value of the measured temperature. Therefore, the outside of the thermocouple maintenance tube should be kept clean to minimize errors.
|
More on that
|
The VG series vision sensor won the MM 2019 Innovative Product of the Year Award
On September 17, 2019, the 15th MM. New Automation Forum in 2019 with the theme of "Interconnection, Integration and Synergy" was successfully held in Shanghai.
|
|
Advantages of digital load cells – Autonex
1. The transmission interval of the digital load cell is long, the communication speed is fast, and the anti-cheating effect is remarkable; The output signal of the traditional analog load cell is small, generally millivolt level, and the signal is still lost due to the damage of the cable resistance during the transmission process, and it is also very simple to be affected by the surrounding environment.
|
|
Autonex humidity sensor features:
Humidity sensors are divided into resistive and capacitive types, and the basic form of the product is to coat the substrate with moisture-sensitive materials to form a moisture-sensitive film. After the water vapor in the air is adsorbed on the moisture-sensitive material, the impedance and dielectric constant of the element are greatly changed, so as to make a moisture-sensitive element.
...
|
|
Autonicus Safety Touchless Door Switches SFN Series
The SFN series of safety non-touch door switches reliably monitors the opening and closing of dedicated actuator doors by means of magnetic detection. This product can be connected to up to 30 units through a dedicated controller, and it can be used vertically and horizontally according to the installation environment, which improves the ease of use.
...
|
|
High Temperature Pressure Sensor Accuracy Affects - Autonex
A high-temperature pressure sensor is a sensor that converts pressure into an electrical signal output, which usually consists of two parts, namely a sensitive element and a conversion element. The sensitive element refers to the part of the sensor that can directly feel or respond to the measurement; The conversion element refers to the sensitive element in the sensor ...
|
|
The difference between switching power supply and module power supply – Autonix
Modular power supplies are power supplies that can be mounted directly on a printed circuit board and feature power supply to application-specific integrated circuits (ASICs), digital signal processors (DSPs), microprocessors, memories, field-programmable gate arrays (FPGAs), and other digital or analog loads.
|
|
Principle and application field of Ottonix panel table
Panel meter, also known as the dial table or meter head, the full name is the panel device instrument (panel device instrument), English Panel Meter. Because this kind of instrument device is fixed on the surface of the equipment for viewing and operation, it is called a panel table, which is a functional part of the screen equipment.
...
|
|
Autonex BD series laser displacement sensors
BD series laser displacement sensor can measure the thickness, width, horizontal difference, parallax, bending, and flatness of the target object by detecting the displacement.
Regardless of the color or material, the sensor provides accurate and reliable measurement results. Sensor head and amplifier unit ...
|
|
The difference between laser sensors and photoelectric sensors – Autonicx
First, the difference in working principle
Photoelectric sensors are controlled by converting changes in light intensity into changes in electrical signals. The laser sensor first emits a laser pulse by aligning it with a laser emitting diode. After being reflected, the laser light is scattered in all directions. Partially scattered light returns to ...
|
|
Autonex SFC series safety controllers
The SFC series of safety controllers can be used with safety input products (switches, sensors, etc.) and satisfies the self-diagnosis function and safety integrity required by safety standards. In addition, the slim design saves space in the installation and allows for the use of screwed/screwless pushes for wiring connections.
|
|
Wiring of the load cell – Autonex
The load cell can be wired in two different ways with input and output:
One is the four-wire connection method
The load cell of the four-wire connection method has no special requirements for the secondary instrument panel, and it is very fast to use, but when the cable is long, it is very easy to be affected by the working temperature.
|
|
The difference between sensitivity, resolution, and accuracy of a sensor
sensitivity
Concept: It refers to the ratio of the change of output △y to the change of input △x in the case of steady-state operation of the sensor, that is, the ratio of the dimension of output and input.
Sensor sensitivity is the slope of the output-input characteristic curve. If the output and input of the sensor ...
|
|
Autonex BD series laser displacement sensors
BD series laser displacement sensor can measure the thickness, width, horizontal difference, parallax, twist and flatness of the target object by detecting the displacement.
Regardless of the color or data of the policy, the sensor can provide accurate and stable measurement results. Sensor head and amplifier unit ...
|
|
Pressure sensor influencing measurement results factor – Ottonix
Pressure is an important parameter in pneumatic, fluid or other measurements, so pressure sensors have been widely used in various experimental measurements, product testing, and automatic control systems, and the stability of the product is a major consideration when purchasing pressure sensors.
...
|
|
Ultrasonic flow sensor principle
Ultrasonic flow sensor is a new type of general-purpose time-difference multi-function ultrasonic sensor suitable for industrial environments, mainly using low-voltage multi-pulse balanced emission acceptance technology, which can be mainly applied to measure the flow of most clean and uniform liquids without large concentrations of suspended particles or gases.
|
|
Rapid detection method for air conditioner thermostat – Ottonix
When the air conditioner cannot operate normally, in addition to checking the starting relay, overheating, overcurrent protector and capacitor of the compressor, it is also necessary to check the main control selection switch of the air conditioner thermostat, which is a very important control protection and actuator component in the electrical control system. Here are a few common types of air ...
|
|
How to install an Autotonics voltage sensor
Voltage sensor refers to a sensor that can sense the measured voltage and convert it into a usable output signal, in a variety of detection and control systems, it is often necessary to track and collect the communication DC voltage signal that changes at high speed, and do spectrum analysis on some more complex voltage waveforms. Voltage Sensors ...
|
|
Advantages of digital torque sensors – Autotonics
In the rotary power system, the most frequently involved parameter: rotational torque, in order to detect the rotational torque, the traditional use of torsion angle phase difference sensors. The more mature detection method of torque testing is strain electrical testing skills. It has high precision, fast frequency response, good reliability, long life, etc.
|
|
Introduction to the principle of temperature controller - Autonix
The temperature controller is an electrical switchgear that controls the temperature of an air-conditioned room. The temperature scale in the air-conditioned room controlled by the temperature controller is generally 18°C--28°C. The temperature controller commonly used in window air conditioners uses the principle of pressure effect to promote the opening and closing of contacts. Its structure consists of bellows ...
|
|
How to use the universal proximity switch safely – Autonex
Proximity switches, as the name suggests, are changes when approaching an object. This type of switch is generally used in mechanical motion, when two objects are approaching, the trigger switch gives a signal, and the control unit (PLC) detects this signal and adopts the next action.
...
|
|
Contact
working hours
