Principle and application field of Ottonix panel table

BD series laser displacement sensor can measure the thickness, width, horizontal difference, parallax, twist and flatness of the target object by detecting the displacement. Regardless of the color or data of the policy, the sensor can provide accurate and stable measurement results. Sensor head and amplifier unit ...

1. Errors in improper introduction of devices In other words, the thermocouple should not be installed too close to the door and the heating place, and the penetration depth should be at least 8-10 times the diameter of the maintenance tube; Maintenance of thermocouples ...

Proximity switch, also known as non-contact travel switch, in addition to being able to complete stroke control and limit protection, is still a non-contact detection device, used to detect the size of parts and speed measurement, etc., and can also be used for the active connection of frequency conversion counters, frequency conversion pulse generators, liquid level control and processing programs.

A high-temperature pressure sensor is a sensor that converts pressure into an electrical signal output, which usually consists of two parts, namely a sensitive element and a conversion element. The sensitive element refers to the part of the sensor that can directly feel or respond to the measurement; The conversion element refers to the sensitive element in the sensor ...

Modular power supplies are power supplies that can be mounted directly on a printed circuit board and feature power supply to application-specific integrated circuits (ASICs), digital signal processors (DSPs), microprocessors, memories, field-programmable gate arrays (FPGAs), and other digital or analog loads.

1. Look at it visually. 2. Verify the sealing and preloading of the system. 3. The pressure sensor is equipped on the pressure standard equipment, including the pressurization (or vacuuming) equipment, and the pressure standard equipment with liquid as the pressure transmission medium should sweep the air in the pipeline. 4 pressure sensors, ...

Dual PID auto-adjustment function There are high-speed response modes and slow reaction modes in the PID function. When you want to reach the desired value quickly, use the high-speed mode (PIDF mode) When you want to minimize overshoot, use slow mode (PIDS mode) ...

The first is the offset error: since the high-frequency pressure sensor maintains a stable straight offset over the entire pressure range, the change in converter diffusion and laser adjustment correction will cause the offset error. The second is the sensitivity error: ...

1. After the modulation pulse generated by the vibration circuit passes through the reflection circuit, the digital integration photoelectric switch or RC integration method is used to eliminate the disturbance, and finally the driver is triggered by a delay (or no delay) to output the photoelectric switch control signal. 2. Use optical elements to make the beam in the middle of the propagation medium.

Capacitive level sensors, ultrasonic level sensors, and discrete photoelectric level sensors. The common development of these three non-touch liquid level sensors is that they are not affected by the color, corrosiveness, pressure, density, etc. of the liquid, because these sensor skills cannot directly lead to the development of liquid ...

The SFN series of safety non-touch door switches reliably monitors the opening and closing of dedicated actuator doors by means of magnetic detection. This product can be connected to up to 30 units through a dedicated controller, and it can be used vertically and horizontally according to the installation environment, which improves the ease of use. ...

First, the first component is blocked or the form of the device is wrong, and the pressure point is unreasonable, so we often emphasize that the device must be the correct device, once it is installed wrongly, or it is not well installed, it will bury endless hidden dangers for the back. What are the primary components? Orifice plates, remote transmission measuring joints, etc.

The PSK1 series is a two-stage display pressure sensor that displays the current value (PV) and the set value (SV) together. It not only shows the setting status, but also provides a power-saving form and a fine-tuning function to improve the user's convenience. PSK1 Key Features: Additional pressure scale (composite pressure ...

Autonics Solid State Relay SSR adds SR(H)2/3 three-phase solid state relay to its family of relays Autonex proudly introduces you to the new formation of solid state relays, three-phase solid state relays. Compact design, flexible devices, easy ...

sensitivity Concept: It refers to the ratio of the change of output △y to the change of input △x in the case of steady-state operation of the sensor, that is, the ratio of the dimension of output and input. Sensor sensitivity is the slope of the output-input characteristic curve. If the output and input of the sensor ...

Cover the safety light curtain with your hands and observe whether the indicator light conversion is normal. During the use of the punch photoelectric protection device, the orientation of the photoelectric protection device shall not be changed at will. In the protection zone, block the light curtain by hand, ...

Performance indicators of load cell: 1. Dynamic characteristics, 2. Linearity, 3. Hysteresis characteristicsDynamic characteristics refer to the output characteristics of the sensor when the input changes. In practice, the dynamic characteristics of a sensor are generally used to indicate how well it responds to certain specification input signals. This is because the sensing ...

1. Percussion hand pressure method It is common to encounter the phenomenon of good and bad operation of the instrument, and most of this phenomenon is due to poor contact or virtual welding. In this case, percussion and hand pressure can be used. The so-called "percussion" is to ...

1. If the electronic ruler is used for a long time, the seal is aging, there are many impurities, and the water mixture and oil will seriously affect the contact resistance of the brush, resulting in the continuous beating of the display. At this moment, it can be said that the electronic ruler of the linear displacement sensor is now damaged and needs to be replaced. ...

The two are not universal Module power supplies are power supplies that can be mounted directly on a printed circuit board, and feature applications for application-specific integrated circuits (ASICs), digital signal processors (DSPs), microprocessors, memories, field-programmable gate arrays (FPGAs), and other digital or analog applications.