Autonex SFC series safety controllers

The first is the offset error: since the high-frequency pressure sensor maintains a stable straight offset over the entire pressure range, the change in converter diffusion and laser adjustment correction will cause the offset error. The second is the sensitivity error: ...

1. If the electronic ruler is used for a long time, the seal is aging, there are many impurities, and the water mixture and oil will seriously affect the contact resistance of the brush, resulting in the continuous beating of the display. At this moment, it can be said that the electronic ruler of the linear displacement sensor is now damaged and needs to be replaced. ...

Reasons: 1. The polar surface of the communication core is uneven or the demagnetization air gap is too large; 2. The double coil of DC operation derived from the communication contactor is overheated due to the fact that the normally closed interlocking contact is not released by welding; 3. The frequency of operation is too high; 4. Poor coil manufacturing or due to mechanical damage, absolute ...

The BH series photoelectric sensors can be used with M18 fixing nuts and fixing nuts for frontal equipment, or with M3 bolts and nuts for peripheral equipment. Sensitive equipment options promise easy application in a variety of industrial environments. The sensor can be equipped with a simple wire to generate individual or simultaneous N...

The load cell can be wired in two different ways with input and output: One is the four-wire connection method The load cell of the four-wire connection method has no special requirements for the secondary instrument panel, and it is very fast to use, but when the cable is long, it is very easy to be affected by the working temperature.

1) The detected object should not touch the proximity switch, so as not to damage the proximity switch due to friction and bumping; 2) Pull the lead wire of the switch by hand will damage the switch close, and it is best to fix the lead wire with a line card at 10 cm away from the switch when the device is installed.

The Ottonix sensor BWC series has selected a 3-point light cross-network detection method to reduce the detection blind spot to the maximum limit, realize the world's leading detection characteristics, and effectively prevent problems that may be caused by direct sunlight, etc., and the detection is more stable. Up to 100 international cutting-edge ...

Dynamic torque transducers can be used in the manufacture of viscometers, electric (pneumatic, hydraulic) torque wrenches, which have the advantages of high precision, fast frequency response, good reliability and long life. Installation process: 1. According to the connection form of the shaft and the length of the dynamic torque sensor, determine the original ...

Key 1: Whether the speed of the motor is normal, whether there is speed jitter and stalled rotation (you can check it with a tachometer). The key is whether the anchor bolts of the motor are loose, whether the root is defective, and whether there are debris around. The key is three, whether the housing and coupling of the motor are defective, ...

The multi-channel pressure indicators of the PSM series can display the measured values of up to 4 or 8 channels of analogue pressure sensors. When used in conjunction with our PSS series pressure sensors, the sensor type, pressure type and range can be automatically recognized without additional settings. Users can also easily ...

1. Check the standard of the equipment hole: Assuming that the standard of the equipment hole is not suitable, some of the threads of the sensor will be slightly worn during the equipment process. This not only affects the sealing performance of the equipment, but also makes the pressure sensor inadequate, and may even cause safety hazards. ...

Autonex has recently launched a new shading action form to add a space for users to choose. The BTF series of ultra-thin photoelectric sensors has a new dark ON form to increase the user's selection space. The selection of self-developed special IC, 3.7mm ultra-thin planning, suitable for small space ...

The TR1D series has a high-speed sampling period of 50ms and a display accuracy of ±0.3% for more accurate temperature control. Simultaneous heating/cooling control is available to provide effective temperature control. With a width of only 22.5mm, the product minimizes the limitation of installation space and can be accessed with ...

BD series laser displacement sensor can measure the thickness, width, horizontal difference, parallax, twist and flatness of the target object by detecting the displacement. Regardless of the color or data of the policy, the sensor can provide accurate and stable measurement results. Sensor head and amplifier unit ...

Pressure is an important parameter in pneumatic, fluid or other measurements, so pressure sensors have been widely used in various experimental measurements, product testing, and automatic control systems, and the stability of the product is a major consideration when purchasing pressure sensors. ...

Infrared sensors include an optical system, a detection element, and a conversion circuit. Optical systems can be divided into two categories: transmissive and reflective according to different structures. According to the working principle, the detection element can be divided into thermal detection element and photoelectric detection element. The most widely used thermistors are thermistors. Thermistor...

Through-beam type BJ15M-TDT-(C)-(P) / BJ10M-TDT-(C)-(P) / BJ7M-TDT-(P) Polarized specular reflective type BJ3M-PDT-(C)-(P) ...

Sensors are the most fundamental and commonly used components in automation systems. Autonex offers a wide range of sensors including proximity switches, photoelectric sensors, fiber optic sensors, and pressure sensors, which are committed to maximizing the user's work efficiency. ​ ...

1. Measure resistance (surface power-off) (1) First use a multimeter to measure the input and output resistance of the load cell, and then compare it with the clarification. If there is a big difference, it will be broken. First, use a multimeter to measure the input and output resistance of the load cell, and then carry out the ...

Autonics continuously improves the product function and quality, so that the product is at the international first-class level. For more than 10 years, the market share of the products in Korea has been maintained. 1. Adopt self-developed special IC ...