A picture to understand the Internet of Things and interactive functions of the HMI touch screen

1. The indicated value is large (or out of range). According to the investigation of our staff, this kind of problem often appears in the atmospheric pressure workshop. When we find that the counterweight of the float in the float level gauge is at a low point, the liquid level must be very high at this time, and the glass plate is inconsistent with the indication of the instrument.

Material metering The measurement of powdery materials is commonly used in the way of screw measurement. The purpose of measurement is achieved by the number of turns of the screw rotation. In order to improve the accuracy of measurement, the speed of the screw is required to be adjustable, and the position positioning is accurate.

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

1. Bearing lubrication failure or bearing surface damage Contaminants can disrupt bearing lubrication and damage bearing surfaces. This will cause the friction to generate heat. If the problem cannot be solved, the increased heat may cause a catastrophic failure of the bearing and the Buke motor to stop running. 2、 ...

Buke MK series all-in-one machine on the market for more than a year, received unanimous praise from many customers, in the Buke "quality first" to create an end-to-end full life cycle product quality management system" and "demand management" under the internal and external drive, through the application feedback of this series of products and in order to fit more ...

1. Encoder connection line failure: This kind of failure has the highest probability and is often encountered in maintenance, so it should be a priority factor. Often, encoder cables are open, short, or in poor contact, so the cable or connector needs to be replaced. Special attention should also be paid to whether the cable is loose and causes open soldering or ...

1. Change the rotational speed by changing the frequency of the mains supply This is a common method of speed adjustment for AC motors. The power supply frequency can be adjusted to the desired speed by adjusting the inverter, transformer, and other equipment. 2. Change the rotational speed by changing the voltage In some special cases ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...

On December 7, Buke was invited to participate in the "2020 China Mobile Robot (AGV/AMR) Industry Development Annual Conference" hosted by the People's Government of Songjiang District, Shanghai and hosted by the China Mobile Robot (AGV) Industry Alliance. At the same time, Buke has also won the "Annual Quality Supply Chain Award" for three consecutive years.

1. Fault code: E-01, E-02 Significance: The parameters are initialized incorrectly during power-on. Cause: Incorrect parameter settings. Solution: Power back on, if the fault is still reported, you need to force the parameter initialization, if it is repeated many times, it cannot be solved.

1. The working principle of servo motor encoder It is a rotary sensor that converts rotational displacement into a series of digital pulse signals that can be used to control angular displacement, and can also be used to measure linear displacement if the encoder is combined with a gear bar or spiral screw. ...

6. The motor vibrates greatly during operation (1) The cause of the failure (1) Due to excessive clearance of worn bearings; (2) uneven air gap; (3) Rotor imbalance; (4) Bending of the rotating shaft; (5) The coaxial axis of the coupling (pulley) is too low. (2) Troubleshooting ...

1. Regularly check the encoder connection line of the servo motor and the power connector of the servo motor to confirm that they are firmly connected; 2. If the servo motor is connected to a reduction gear, the servo motor should be sealed with oil to prevent the oil from the reduction gear from entering the servo motor. ...

1. The first difference between a servo encoder (synchronous service motor) and an ordinary encoder is that it provides sensing signal feedback for the commutation of the starting current. The main performance indicators of servo motor encoders are shift rate, accuracy, and repeatability. 1) Routinely mentioned 17-bit to 25-bit singleturn resolution ...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

AC motor speed regulation is achieved by changing the electrical parameters such as the power supply frequency, number of pole pairs and slip rate of AC motor. 1. Use the inverter to change the power supply frequency speed regulation, the speed regulation range is large, the stability and smoothness are good, and the mechanical characteristics are hard. It's just to add the amount ...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

Due to the limitations of technology and environmental adaptability, the surface touch screen will not be able to be used normally due to water droplets, dust and other pollution not being treated in time, so the touch screen also needs regular maintenance like ordinary machines. And because the touch screen is a variety of electrical equipment high ...

1. Servo motor encoder is a product installed on the servo motor, which is equivalent to a sensor. 2. Do speed closed-loop and azimuth closed-loop to complete accurate speed regulation and accurate azimuth control. 3. The servo motor has its own encoder, which can be converted into servo electronic gears.

A servo motor encoder failure means that the encoder component is faulty, preventing it from generating and outputting the correct waveform. In this case, the method of repair is to replace the encoder or repair its internal parts. 1. Encoder connection line failure: this kind of failure has the highest probability of repair...