Buke servo motor - servo motor encoder selection attention

In terms of the response speed of the servo drive: the torque mode has the smallest amount of calculation, and the driver responds the fastest to the control signal; The position mode is the most computationally intensive, and the driver is the slowest to respond to the control signal. When there are relatively high requirements for dynamic performance in motion, it is necessary to ...

6. When the motor is unloaded and overloaded, the ammeter pointer is unstable and swings 1. Cause of failure (1) The cage rotor guide bar is welded or broken; (2) Winding rotor fault (one-phase break) or poor contact of brushes and collector ring short-circuit devices. 2. Troubleshooting ...

1. Check whether the power supply voltage is stable and whether the logic voltage is within the input range of the driver, and use a separate power supply to supply power to the logic circuit; 2. The target current limit is set too small, and the current limit is increased within the allowable range. If you still can't find the reason for the above solutions, please ...

What are the power requirements for hardware setup 1, ED100 and ED200? The logic power supply of the Kinco servo is DC24V (scale is 18V-30V), not less than 1A (if the boundary says OUT and Brake output, it is not less than 2A); The power supply of ED100 is DC24V-DC70V, and the power supply requirements of ED200 and ED216 are D...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

· They offer significant cost-effectiveness · They provide smoother operation · they are very efficient and tend to reduce energy costs · can optimize thermal management by embedding the motor into the machine · They offer improved servo performance and therefore improved production ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...

Material metering The measurement of powdery materials is commonly used in the way of screw measurement. The purpose of measurement is achieved by the number of turns of the screw rotation. In order to improve the accuracy of measurement, the speed of the screw is required to be adjustable, and the position positioning is accurate.

1. Install the rotating shaft on the equipment casing, and the spindle and the equipment casing are supported by bearings. 2. Install the stator on the stop of the equipment housing and press it with the stator pressure ring. 3. Put the rotor into the inner hole of the stator, pay attention to protect the stator at the same time, and use the connecting bolt to connect the rotor with the ...

(1) Encoder failure: It refers to the failure of the components of the encoder itself, resulting in its inability to generate and output correct waveforms. In this case, the encoder needs to be replaced or its internal components repaired. (2) Encoder connection cable failure: the probability of this fault is the highest, and the maintenance ...

Daily maintenance of the touch screen: 1. The capacitive touch screen should generally be filmed, and it should be pasted well. membranes (double-layer membranes) that meet ESD standards; 2. The capacitive touch screen is cleaned regularly, and the liquid crystal cleaning solution used for the computer is used (alcohol and furniture cleaning liquid cannot be used); 3. Transport...

1. The indicated value is large (or out of range). According to the investigation of our staff, this kind of problem often appears in the atmospheric pressure workshop. When we find that the counterweight of the float in the float level gauge is at a low point, the liquid level must be very high at this time, and the glass plate is inconsistent with the indication of the instrument.

1. Communication cannot be connected. 2. The interference in the process of data transmission will increase (sometimes it is not bad, but the connection between the host computer and the servo is incorrect, or there is a falling off, which is a very common problem). 3. The motor will run, but it will not work according to the instructions given by the servo ...

Human-computer interaction refers to the interaction between humans and machines, which is essentially the interaction between humans and computers. Or more broadly: human-computer interaction refers to the interaction between a human and a machine containing a computer. Specifically, the two-way communication between the human-computer interaction user and the machine containing the computer ...

Frameless torque motor is a new type of direct-drive torque motor, which is designed for applications that require small size, light weight, low inertia, low cogging torque, and high power. High reliability - no mechanical transmission, long life and easy installation. Serialized products are not limited to the following types ...

1. The working principle of servo motor encoder It is a rotary sensor that converts rotational displacement into a series of digital pulse signals that can be used to control angular displacement, and can also be used to measure linear displacement if the encoder is combined with a gear bar or spiral screw. ...

1. The motor temperature is too high or the smoke is faulty Cause: 1. Excessive load 2. Two-phase operation 3. Air duct blockage 4. The ambient temperature increases 5. Stator windings are short-circuited between phases or turns 6. Stator winding grounding 7. The power supply voltage is too high ...

1. The basic functions and selection indicators of human-machine interface products Basic Functions: Display of equipment working status, such as indicator lights, buttons, text, graphics, curves, etc.; Data and text input operations, printouts; Production recipe storage, equipment production data ...

1. Check the servo motor to ensure that there is no fatal damage outside; 2. Check the fixed parts of the servo motor to ensure that the connection is strong; 3. Check the output shaft of the servo motor to ensure the rotation and circulation; 4. Check the encoder connection line of the servo motor and the ...

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...