Buke servo drive - the wiring method of the stepper driver and PLC

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

Cause of the failure 1) The sound wave reflection stripes on the four periphery of the surface sound wave touch screen are seriously dusty or scale, resulting in the touch screen not working. 2) The touch screen is malfunctioning. 3) The touch screen control card is faulty. 4) The touch screen signal line is faulty ...

1. Hydraulic servo control system The hydraulic servo control system is based on the power provided by the motor, and the hydraulic pump is used to convert the mechanical energy into pressure and push the hydraulic oil. By controlling various valves to change the flow direction of the hydraulic oil, so as to push the hydraulic cylinder to make different strokes, different directions of the movement...

1. Check the servo motor to ensure that there is no fatal damage outside; 2. Check the fixed parts of the servo motor to ensure that the connection is strong; 3. Check the output shaft of the servo motor to ensure the rotation and circulation; 4. Check the encoder connection line of the servo motor and the ...

On December 7, Buke was invited to participate in the "2020 China Mobile Robot (AGV/AMR) Industry Development Annual Conference" hosted by the People's Government of Songjiang District, Shanghai and hosted by the China Mobile Robot (AGV) Industry Alliance. At the same time, Buke has also won the "Annual Quality Supply Chain Award" for three consecutive years.

MT4000 series MT4000 series HMI is a sub-series of eView HMI, which is one of Buke's HMI products Series, human-machine interface MT4000 is referred to as ordinary application series. MT4000 series HMI products adopt 32 ...

1. When the motor rotates, the LED light flashes (1) Cause of failure: HALL phase error. Solution: Check whether the motor phase setting switch is correct (2) Fault cause: HALL sensor failure, treatment method: When the motor rotates, detect the voltage of HalA, HalB, HalC ...

One. SERVO MOTOR DIMENSIONS: 38MM, 58MM, 66MM, 80MM.100MM. Two. Servo motor encoders are divided into: singleturn, multiturn. Three. Servo motor encoders are divided into magnetic absolute encoders and photoelectric absolute encoders according to the principle Four. Servo motor ...

1. The servo mechanism is an automatic control system that enables the position, orientation, state and other output controlled quantities of the object to follow the arbitrary change of the input target (or given value). The servo mainly relies on the pulse to position, which can basically be understood in this way, the servo motor receives 1 ...

1. Change the rotational speed by changing the frequency of the mains supply This is a common method of speed adjustment for AC motors. The power supply frequency can be adjusted to the desired speed by adjusting the inverter, transformer, and other equipment. 2. Change the rotational speed by changing the voltage In some special cases ...

1. Excessive load: Confirm whether the connected load exceeds the rated load capacity of the drive. The load is too large and needs to be reduced appropriately to ensure that the current is within the allowable range. 2. The driving system parameter setting is incorrect: check whether the driver parameter setting is correct. 3、 ...

1. Start the servo motor before work (1) Measure the insulation resistance (0.5M or more for low-voltage motors). (2) Measure the power supply voltage, check whether the wiring of the motor is correct, and whether the power supply voltage meets the requirements. (3) Check whether the starting device is normal. ( ...

1. Encoder connection line failure: This kind of failure has the highest probability and is often encountered in maintenance, so it should be a priority factor. Often, encoder cables are open, short, or in poor contact, so the cable or connector needs to be replaced. Special attention should also be paid to whether the cable is loose and causes open soldering or ...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

1. The motor temperature is too high or the smoke is faulty Cause: 1. Excessive load 2. Two-phase operation 3. Air duct blockage 4. The ambient temperature increases 5. Stator windings are short-circuited between phases or turns 6. Stator winding grounding 7. The power supply voltage is too high ...

Boost machine performance Direct coupling (no backlash) Higher system bandwidth Improve machine efficiency More compact structure The machine takes up less space The highest torque per unit volume Reduced maintenance Fewer mechanical parts No grinding ...

1. Sweeping: Sweeping is generally caused by friction of the stator and rotor due to bearing damage, shaft bending, or improper assembly during maintenance. In the process of overhaul and assembly of the motor, the parts of the motor should be kept clean, and the assembly of the end cover, bearing, etc. should be reasonable and not barbaric construction, otherwise ...

Human-computer interaction refers to the interaction between humans and machines, which is essentially the interaction between humans and computers. Or more broadly: human-computer interaction refers to the interaction between a human and a machine containing a computer. Specifically, the two-way communication between the human-computer interaction user and the machine containing the computer ...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.