Graphic tutorial for the installation of OTC welding robot relay device plus I/O board

E1064 Handling of Unstable Exceptions Detected in Sequential Circuits. 1. Shut down and restart. 2. After the shutdown and restart are invalid, remove the sequence board and reinstall it. 3. If it doesn't work ...

1. Preparation before robot maintenance 1. Robot oil type: REO about 1000ml, EP2 about 10-30ml, WR2 about 10ml 2. Tools: one technical refueling pump, 4 syringes, oil blotting paper, several plastic bags, waste oil drums, hexagonal wrenches 3. Robot ...

1. Improve the authority of the robot to handle: Turn on the power supply of the robot control box and enter the main interface of the teach pendant: As shown in the figure above, press to enter the R function code interface, enter 314, and then, enter the authority password 12345, and then. You can carry out the robot handling operation. ...

In recent years, China's industrial robot industry has entered a period of rapid growth, and has become the world's largest shopping mall for six consecutive years. In the development of industrial robots, there was a hot together, the concept of hype that existed at that time, rushed ...

Generally speaking, welding robots need to carry out electrode grinding operations after long-term operation. This is due to the fact that after the robot has been welded repeatedly, the shape of the electrode tip may change, that is, the electrode will be worn, resulting in the welding quality of the robot.

The OTC robot needs to adjust the tension of the belt once a year or every 3,000 hours of work, whichever is shorter. The OTC robot B4 (B4L) is used as an example to introduce the adjustment method and precautions. The timing belt of the OTC robot B4\B4L is located in the motor and reduction gear.

Customer Requirements: Due to the small working space, the robot needs to be installed close to the wall, or installed on the shelf or platform, saving the overall floor space! In addition, a robot system is needed to be able to complete the cutting of H-beams, improve the overall production efficiency, and improve the ...

1. Stable center of gravity Welding is like practicing martial arts, the first thing to do is that the chassis should be stable, that is, the "horse step" should be stable, and the center of gravity cannot be unstable, and it is difficult to weld a good weld when the welding is shaking. 2. The welding torch should be stable Trembling words ...

Fault phenomenon: the manual operation is normal, after the automatic form is converted, the red light in the stop state does not go out, but press strat (start) once, and the program takes a step. Solution: Ask the manufacturer for the treatment method, and the reason is that the operation mode of the machine has been changed to stop in one step (1STEP). ...

When the encoder battery low alarm cannot be recovered, the encoder orientation information is lost, and it is necessary to reset the operation: 52 encoder failure encoder batterycharge low1016 1. Replace the robot ...

1. The axis key for controlling the movement of the junction is mainly used to adjust the orientation and viewpoint of the robot and the welder. When the SW switch is pressed, the cooperative coordinates can be used to control the robot's orientation. 2. The coordinate switch button can be used in the axis ...

1. Keep the surface of the palletizing robot clean and clean up the dust in time; 2. Check whether the fixing bolts of the palletizing robot are loose once a week; 3. Smooth the cylinder support shaft, hinch seat hole and shaft every day. 1-2 drops of smooth oil per filling; ...

The OTC arc welding robot has five optional special sensor accessories for arc welding, which are FD-WD, FD-AR, FD-QD, FD-QF, FD-QT. During this period, the introduction of each type of arc welding special sensor equipment is as follows: 1. ...

1. The power supply of industrial robots is generally a communication servo motor. Because of the pulse signal drive, the servo motor itself can complete the speed conditioning of industrial robots and generally repeat the same process; 2. In order to ensure that industrial robots can be reliably ...

In the window, click "robotkr210r2700_extra", and then in the menu, under the "Commands" menu, click the command button RobotJog, which guides the manual operation panel to open and move the robot to the appropriate position. ...

1. Insist on 1/4-3/8 inch wire rod elongation (the length of the wire protruding from the torch head). 2. Use small diameter welding wire when welding thin plates; When welding thick plates, large diameter welding wire and high-current welding machine are used. See welder recommendations ...

1. 3 years warranty in the industry (body, control box, teaching box, operation box, control cable) 2. Full Chinese operation interface, simple and easy to understand, together can support 6 language selection; 3. The working radius is long, and the working radius of the standard welding robot can reach 1.4 meters or 2 meters (not included).

1. The only warranty in the industry for 3 years (body, control box, teaching box, operation box, control cable); 2. Full Chinese operation interface, simple and easy to understand, and can support 6 language selection; 3. Long working radius, standard welding robot working radius up to 1.4 meters or 2 meters (not...

Spot welding tong: used to realize the pressurization of the welded workpiece (plate). The welding tongs used by the robot are usually the transformer and the clamp body are installed together to form a whole, which is called "one-piece welding tong". In practical use, it is necessary to make special measures for the welding tong body according to the particularity of the dotting position.

1. How to identify targets accurately and at high speed (in real time). 2. How to effectively construct and arrange a reliable identification algorithm and implement it successfully? We look forward to new breakthroughs in high-speed matrix processing units and algorithms such as neural network approaches and wavelet transforms, so that the most advanced kernels can be used with minimal cores.