Generally, there are three buttons to provide the need for setting, one is the Set button, press it once to enter the setting state. The other two offer upward and downward temperature adjustments, which can be adjusted to any temperature point. After adjusting to the desired temperature point, press the Set button again to confirm.
1. Turn on the power of the smart thermostat, and the current temperature is displayed on the display. Because the sensor is not in contact with other devices, but is exposed directly to the air, this is the current temperature: 31 degrees Celsius, which is not too hot.
2. At the bottom right of the display is the "Start Temperature" setting button, press the heating button once, and the temperature will increase by 1 degree Celsius; You can also press and hold and not let go, and the temperature will rise continuously. Here I set it to 65 degrees Celsius, that is, when the sensor temperature is lower than or equal to 65 degrees, the output socket will automatically power on and the connected device will start. The equipment can be an electric motor, an electric heater, and many more.
3. At the bottom left of the display is the "Stop Temperature" setting button. I set it to 80 degrees, that is, when the sensor temperature is higher than or equal to 80 degrees, the output socket will automatically power off and the controlled device will stop working.
4. Look at the temperature sensor again, its function is to sense the temperature of the monitored object, and convert it into an electrical signal, which is transmitted back to the thermostat through the wire. You can try it with a ferrous object, the sensor has strong magnetism and can be adsorbed on it.
5. Attach the sensor to the equipment to be monitored. The device has to have an iron part; Otherwise, you have to find a way to fix it.
6. Plug the controlled device into the thermostat output outlet. Note: It is best to do this when the thermostat itself is not powered on. At this point, the setup is complete, the thermostat is powered on, and the system is working.
|
More on that
|
RLC thermostats – the classification of thermostats and their detailed introduction
1. Sudden jump thermostat
The type of various sudden thermostats is collectively called KSD, such as KSD301, KSD302, etc., the thermostat is a new type of bimetal thermostat, mainly as a variety of electric heating products with overheat protection, generally connected with the thermal fuse in series, sudden temperature ...
|
|
RLC Thermostat – The reason why the temperature control meter shows HHH
The reasons why the temperature control table shows HHH are as follows:
1. The thermocouple signal line is reversed, or short.
2. If the temperature control meter is in normal use before, it is recommended to check whether the signal line of the thermocouple is broken.
3. The wire inside the thermocouple is broken.
4 ...
|
|
RHK thermostat - the thermostat shows the reasons for the deviation between the temperature and the actual temperature and the solution
The thermostat shows a nonlinear relationship between the temperature and the actual temperature deviation:
(1) The input type of the thermostat is selected incorrectly;
(2) There is no calibration or calibration error in the analog input;
(3) There is interference in the thermostat;
(4) There is interference with thermocouples;
(5) The use of quality is not ...
|
|
RKC Level Gauges - Advantages and Disadvantages of Several Common Level Gauges Introduction
1. Float level gauge is an instrument that relies on the principle of buoyancy to measure the liquid level. Usually by means of a float in conjunction with a scale, the observer can visually read the height of the liquid level.
Advantages: fast and intuitive reading; Low price; Easy to install.
Shortcoming:...
|
|
Key features of the RLC thermostat:
Thermocouples, RTDs, analog and other signals are freely inputted, and the range can be set freely;
The software zeros the full degree, the cold end measures the temperature separately, the amplifier is self-stabilizing, and the display accuracy is better than 0.5%FS;
Fuzzy theory combined with traditional PD method, fast and stable control, advanced tuning ...
|
|
Where you need to pay attention to the wiring of the RRKC thermostat
1. For thermocouple input, the corresponding compensation wire should be used.
2. RTD input, 3 wires with low resistance and no difference should be used.
3. The input signal line should be far away from the power line of the instrument. Power supply and load lines to avoid noise interference.
4. Instrument power cord ...
|
|
Parameter setting operation of RLC temperature control table CH402
Model: CH402FS01-8*HN (for PECVD temperature control)
1) Single press SET: SV can be set (set temperature manually)
2) Press and hold the SET button for 2 seconds, ALI=1000 (absolute alarm temperature setting) and then press the SET button, ATU=1 (self-defining, self-interpreting a set of PID parameters) to exit ...
|
|
RLC Thermostat - Introduction to the function of mechanical temperature control
1. The temperature setting is set by the knob, which is convenient and intuitive 2. It can be directly installed on the standard junction box on the wall.
3. Beautiful appearance and reliable performance.
4. The switch adopts toggle type, which feels comfortable and has a long life.
5. It can control two-wire or three-wire electric (ball...
|
|
Common faults and failure analysis of RTC thermostats
1. The power indication is normal, but the temperature controller has no screen display. Most of this fault is caused by the heating of the voltage regulator element (7805 or 7812) on the thermostat during long-term use, which leads to the breakpoint of the solder joint, and sometimes it is caused by the phenomenon of virtual soldering at the factory, and the main re-soldering can be done.
2. Temperature controller ...
|
|
RKC thermostat – the correct way to adjust the thermostat
1. Set temperature: Press the SET button to set or view the temperature set point. Press the SET key digital tube character start flashing, indicating that the appearance has entered the setting state, press the △ key to increase the set value, press the ▽ key to decrease the set value, press and hold the △ key or ▽ key The data will change rapidly, press the SET key again The appearance will return ...
|
|
RRKC Thermostat – Questions and Precautions About Thermostat Expansion Modules
1. Under what circumstances should I use a thermostat to expand the module?
The gradual development of the heating field is now very well recognized, and more and more users have begun to install electric heating, of course, when installing electric heating for users, they have also encountered some headaches.
For example, a large area ...
|
|
How the thermostat works – RKC
Thermostat, according to the temperature change of the working environment, physical deformation occurs inside the switch, so as to produce some special effects, a series of automatic control elements that produce on-on or off-action actions, or different principles of electronic components at different temperatures and working states to give ...
|
|
The main role and service life of the thermostat - RLC
In most cases, in Europe, the thermostat is a necessary accessory for the wall-hung boiler, and the two are delivered to the user at the same time, and most of the thermostats equipped are intelligent thermostats. In China, nearly 95% of the wall-hung boilers that have been installed in operation and are being installed and debugged and ready to be put into use are not equipped in advance.
|
|
RK thermostat - the problem that should be paid attention to in the installation of floor heating thermostat
1. Wall installation, the height is about 1.2 meters, generally on the same horizontal line as the electric lighting switch of the home.
2. Installed on a wall where the surrounding air flows freely, and is not affected by other heat sources (e.g. sunlight), air flow from doors and windows, or external wall temperature, etc.
3. Advance ...
|
|
Physical and chemical RK C thermostat - dry-type transformer thermostat shows fault handling methods
1. The dry-type transformer thermostat does not appear
Cause of failure: (1) The power supply of the thermostat is not connected; (2) The fuse is blown out.
Solution: (1) Turn on the power supply; (2) Replace the fuse.
2. The dry-type transformer thermostat shows that one or three phases are shining and showing "-OP-"
...
|
|
Common faults and solutions of intelligent temperature controllers - RTC
Master the common problems of several common intelligent temperature controllers, and solve them by yourself when you encounter problems, and you don't need to spend time and effort to find someone to repair, the common problems are as follows:
1. Heating for a period of time, the temperature does not change. Ambient temperature (e.g., room temperature 25°C) is displayed at all times
...
|
|
Precautions for the selection of RRKC thermostats
The following points should be paid attention to in the selection of intelligent thermostats:
(1) Dimensions (panel size, length)
(2) Enter the sensor graduation number (according to the matching sensor), display accuracy, and display resolution
(3) What is the main output (selected according to the controller)
...
|
|
Introduction to the types of alarms for RRKC thermostats
* Alarm table {ALM1} (standard built-in)
A: Upper limit deviation alarm G: Standby upper and lower limit deviation alarm attached
B: Lower limit deviation alarm H: Upper limit input value alarm
C: Upper and lower limit deviation alarm J: Lower limit input value alarm
D: Alarm in the range K: Attached standby ...
|
|
RHK thermostat - 5 common problems and solutions for stand-alone thermostats
Fault 1: The thermostat does not turn on (does not light up)
Analyze the causes
1. Wrong wiring
2. The voltage of the input terminal is not enough or the input terminal is damaged by empty opening and leakage
3. Whether the cable between the panel and the power board is broken or plugged incorrectly
4. Load short circuit or open circuit, probe ...
|
|
RKC Level Gauge – Some installation requirements for pontoon level gauges
1. The installation of the level gauge must be vertical to ensure that the inner pontoon can move up and down freely in the pipe body.
2. Install a shut-off valve between the container and the liquid level gauge to clean and overhaul the liquid level timing to cut off the material.
3. No magnets are allowed to approach around the main body of the pontoon level gauge, otherwise ...
|
|
Contact
working hours
