At LogiMAT 2022, an independent jury of scientists and journalists recognized Bosch Rexroth's autonomous mobile robot (AMR) ActiveShuttle as the "best product" in the category "Order picking, conveying, lifting and storage technology". As a ...

1. The filter on the suction pipeline is blocked; 2. The oil level of the hydraulic oil tank is too low; 3. The R angle of the variable mechanism is too small, so that the flow rate is too small, and the influence of internal leakage is added, so it cannot continuously supply pressure oil to the outside world; 4. The strain between the oil distribution pan and the contact surface of the cylinder block is serious, and it is not sealed or ...

1. Check whether the piston pump is damaged and corroded, and replace it if so. 2. Check the fit of the plunger pair. Insert the end of the plunger into the plunger sleeve, tilt it about 60°, and if the plunger can slide slowly under its own action, it will fit well. 3. Check the tightness of the plunger pair. Use...

From smartphones to electric vehicles, the need for compact, reliable, and durable batteries is driving many battery manufacturers to ramp up production capacity quickly. But these highly automated battery assembly lines often take months to develop. So, can the speed be accelerated? 　　DWFritz Automa ...

1. Determine the pressure The rated pressure of the selected metering pump is slightly higher than the actual maximum pressure required, generally 10-20% higher. Don't choose too high, too much pressure will waste energy, increase the investment and operating costs of the equipment. 2. Determine the flow rate Selected ...

Efficient hydrogen compression can halve the total cost of ownership for operators More economical delivery helps to reduce the price of hydrogen refueling Automatic seal replacement for easier maintenance 　　The container-based hydrogen compressor MAX Compression 2.0 is equipped with a digital hydraulic system from Bosch Rexroth ...

1. Workload cycle 2. Oil type 3. Minimum flow rate and maximum flow 4. Pressure range 5. System type: open system or closed system 6. Ambient temperature, system working temperature and cooling system 7. Oil pump type: gear pump, ...

1. High parameters: high rated pressure, high speed, high driving power of Rexroth oil pump 2. High efficiency, the volumetric efficiency is about 95%, and the total efficiency is about 90%. 3. Long lifespan 4. Variables are convenient and have many forms 5. Light weight per unit power 6. Force ...

The easy-to-set up, highly integrated mechatronic subsystem provides a more efficient engineering handling solution. With the new Cartesian multi-axis system, Bosch Rexroth linear drive technology offers you a valuable competitive advantage. The handling robot, which consists of linear axes, flows through the entire value ...

1. Quantitative pump + relief valve system This is the most basic and low-cost hydraulic pump system, because the displacement of the pump is fixed, and the output flow is fixed under the condition that the speed of the prime mover is unchanged; A part of the flow drives the load, and the excess flow is returned to the tank through the relief valve, and the overflow ...

There are 3 precautions when installing a hydraulic pump in the hydraulic system: 1. The coaxiality deviation between the hydraulic pump drive shaft and the motor drive shaft is less than that, and the flexible coupling joint is generally used, and the V-belt is not allowed to directly drive the pump shaft to rotate, and the pump shaft is subjected to excessive radial force, which affects the normal operation of the pump; 2 ...

1. Frequent grease, the electric oil drum pump is running at high speed, and the grease is easy to volatilize, so it is necessary to keep the lubrication at the bearing clean and pay attention to the replacement. 2. Pay attention to the storage of the electric pumping pump should be placed in a dry, clean and no corrosive gas environment. 3. Gear oil ...

1. According to the layout of the device, terrain conditions, water level conditions, and operating conditions, determine the selection of horizontal, vertical and other types (pipeline, submersible, submersible, non-clogging, self-priming, gear, etc.) gear pumps. 2. According to the nature of the liquid medium, determine the water gear ...

During the meshing process of the gear pump, the number of gear pairs meshed at the same time should be more than one pair, that is, the overlap coefficient ε should be greater than 1 (ε=1.4) to work normally. The oil left between the teeth is trapped in an enclosed space formed by two pairs of teeth meshing at the same time, and the volume of this space will be ...

1. What should I pay attention to when using a gear pump? (1) The oil suction height of the gear pump shall generally not be greater than 500mm. (2) The gear pump should be directly connected with the motor through the flexible coupling, generally not rigidly connected or connected with the power source through the gear pair and belt mechanism, so as to avoid unilateral force, ...

1. According to the form of gear meshing, it can be divided into: external meshing and internal meshing 2. According to the tooth shape curve, it can be divided into: involute tooth form and cycloidal type 3. According to the form of the tooth surface, it can be divided into: spur gear type, helical gear type, herringbone gear type, arc tooth surface gear type 4. Press ...

In modern construction machinery, basically inseparable from hydraulic working devices, even if the main working devices do not use hydraulic equipment, usually need hydraulic systems to achieve some auxiliary work, hydraulic pressure is so important, and our life and work is very close. Image But...

Want to carry out moving tasks with ease? Let the Bosch Rexroth Smart Handling Function Kit help you. Thoughtfully conceived and easy to set up, this mechatronic kit significantly reduces the time required to design handling solutions and takes your productivity to a whole new level. Why...

(1) Remove the burrs from each part. The sharp edge of the gear is poured with natural oil stone, but not into a fillet. The parts after flat grinding should be demagnetized, and all parts should be carefully cleaned with kerosene before they can be put into assembly. (2) Measure and ensure the axial clearance during assembly: Rexroth gear oil pump axial ...

It's hard to imagine a factory automation system without linear robots. The application of linear robots involves handling incoming materials during product production, assembly or packaging, whether integrated into a single machine as a pick-and-place unit or integrated into a semi-automatic or fully automated production line. However...

For the field of profiling cutting, there is a growing demand to increase productivity and shorten set-up times and CNC interpolation time. The Bosch Rexroth MTX CNC system provides the perfect basis for machine builders and users to meet the growing challenges and at the same time comply with the requirements of the OPC UA standard for Industry 4.0 communication ...