1. Wall installation, the height is about 1.2 meters, generally on the same horizontal line as the electric lighting switch of the home.
2. Installed on a wall where the surrounding air flows freely, and is not affected by other heat sources (e.g. sunlight), air flow from doors and windows, or external wall temperature, etc.
3. Pre-embedded electrical cassette, standard 86 cassette, recommended cassette depth should reach 50mm. In particular, due to the fact that the size of the European and American thermostats does not match the size of the 86 type cassette in China, please confirm it before embedding. Keep the inner cavity of the cassette clean and remove the debris left over from the decoration.
4. The installation of external sensors (ground probes) requires embedded casing to ensure easy unplugging and unplugging during installation and maintenance. The ground of the casing should be sealed to prevent moisture and debris from entering.
5. Do not install the thermostat in the bathroom, sauna, steam room (high humidity or wall that may splash water), in this case, the thermostat must be installed outside, and the lead of the extended probe is used to control the ground temperature.
6. The thermostat of the water heating system can provide a synchronous (or programmable) passive linkage port with the valve control, which can realize the linkage control with the wall-hung boiler and the system pump.
7. The total load of the thermostat of the electric heating system should not be greater than 3500W (the current is less than 16A). Particular attention should be paid to the reliable connection between the load cable and the terminals.
8. Reserve cables with sufficient current according to the power of the electric load.
9. The power supply of the floor heating system must be equipped with independent electrical circuits, with the functions of safety cut-off and leakage protection.
10. Due to the space limitation of the wall cassette, the initial installation of the thermostat may encounter many problems such as small space, difficult wiring, and uneven pressure. Please be patient and carefully read the instructions, follow the correct steps, or call the manufacturer.
|
More on that
|
RLC Thermostat - Introduction to the function of mechanical temperature control
1. The temperature setting is set by the knob, which is convenient and intuitive 2. It can be directly installed on the standard junction box on the wall.
3. Beautiful appearance and reliable performance.
4. The switch adopts toggle type, which feels comfortable and has a long life.
5. It can control two-wire or three-wire electric (ball...
|
|
RRC thermostat - introduction to the working principle and classification of electronic thermostats
Principle of electronic thermostat:
The electronic temperature controller (resistive type) is measured by the method of resistance temperature sensing, and generally uses platinum wire, copper wire, tungsten wire and semiconductor (thermistor, etc.) as the temperature measurement resistor, which has its own advantages and disadvantages. Household Air Conditioner Temperature Controller ...
|
|
The main role and service life of the thermostat - RLC
In most cases, in Europe, the thermostat is a necessary accessory for the wall-hung boiler, and the two are delivered to the user at the same time, and most of the thermostats equipped are intelligent thermostats. In China, nearly 95% of the wall-hung boilers that have been installed in operation and are being installed and debugged and ready to be put into use are not equipped in advance.
|
|
RRKC thermostats – about output and control performance
When using a temperature controller to control a heater, it is necessary to convert the control calculation results of the temperature controller into electricity and apply it to the heater. Electromagnetic relays, solid state relays or phase controllers are usually used for conversion. Depending on the conversion method, the output of the temperature controller is different ...
|
|
RK Thermostat - The working principle and device precautions of liquid expansion thermostat
How liquid expansion thermostats work
Liquid expansion thermostat is a physical phenomenon (volume change) that causes the material (generally liquid) in the temperature sensing part of the thermostat to undergo corresponding thermal expansion and cold contraction when the temperature of the controlled object changes, and the diaphragm box connected with the temperature sensing part expands or ...
|
|
The debugging method of the temperature controller
Generally, there are three buttons to provide the need for setting, one is the Set button, press it once to enter the setting state. The other two offer upward and downward temperature adjustments, which can be adjusted to any temperature point. After adjusting to the desired temperature point, press the Set button again to confirm.
1. Turn on the smart thermostat ...
|
|
What should I pay attention to when setting up my RKC thermostat?
Wiring Warning:
If the instrument fails or an error occurs, which can cause a system failure, an external protection circuit is installed to prevent such accidents:
In order to prevent damage or failure of the instrument, choose an appropriate fuse to protect the power cord and input and output lines from strong power shocks.
Power supply ...
|
|
RKG thermostat - an introduction to the relevant knowledge of temperature controllers
The temperature controller is an electrical switchgear that controls the temperature of an air-conditioned room. The temperature range in the air-conditioned room controlled by the temperature controller is generally 18°C--28°C. The temperature controller commonly used in window air conditioners uses the principle of pressure to push the contacts on and off. Its structure consists of bellows ...
|
|
RKC converters – what are the functions of converters?
1. Power conversion: convert the voltage (rated 100V) and current (rated 5A or 1A) of the transformer into voltage (several volts) to meet the requirements of weak current components.
2. Isolation: current, secondary side security, and work grounding are used to ensure the safety of people and equipment, while weak current ...
|
|
RRKC thermostat - five common faults and solutions of smart thermostats
After heating for a while, the temperature does not change. Displays the ambient temperature of the site at all times (e.g. room temperature 25°C)
In case of such a fault, first check whether the SV value setting value is set, whether the OUT indicator of the meter is lit, and whether the No. 3 and No. 4 terminals of the meter are 12VDC output with the "multimeter". ...
|
|
RKC Thermostat Usage Warning
· Wiring warning:
- If the instrument fails or an error occurs, which can cause a system failure, install external protection circuits to prevent such accidents;
- To prevent damage or failure of the instrument, use appropriate fuses to protect the power cord and input/output cord from strong power shocks.
...
|
|
What are the rich functions of RRKC thermostats – wall mounted thermostats?
The wall-mounted thermostat is an ultra-thin intelligent thermostat that integrates measurement, display, control, alarm, recording and other functions, which can realize accurate measurement and control of temperature, pressure, flow and other parameters. Available in three sizes of 5 inches, 7 inches and 9 inches, a total of 12 models are available ...
|
|
RKC converter – the control strategy of the converter
Direct transformation method
The direct conversion method is to synthesize the "output voltage" through the continuous chopping of the input voltage, which can be divided into coordinate transformation method, harmonic injection method, equivalent conductivity method and scalar method, although all these methods have certain advantages, but also have certain problems, ...
|
|
Key features of the RLC thermostat:
Thermocouples, RTDs, analog and other signals are freely inputted, and the range can be set freely;
The software zeros the full degree, the cold end measures the temperature separately, the amplifier is self-stabilizing, and the display accuracy is better than 0.5%FS;
Fuzzy theory combined with traditional PD method, fast and stable control, advanced tuning ...
|
|
RKC Level Gauge - Preservation and storage of float level gauges in daily use
1. To avoid damage to the instrument, pay attention to the correct protection method: in order to ensure the accuracy of the instrument and avoid damage to the instrument, try not to use the protection instrument of isolator or other isolation devices. If you have to do it, you should also pay attention to the careful selection, determine the isolation solution, and wash the isolation film correctly, ...
|
|
RKC thermostat - introduction of the three output modes of the thermostat
The first output method is relay output, which is output for temperature control through the switching signal of the relay on/off, which is used to directly control the load less than 5A, or directly control the contactor and the intermediate relay, and control the high-power load externally through the contactor.
The second ...
|
|
RLC thermostat - a detailed explanation of dry-type transformer thermostats
The working principle of dry-type transformer thermostats
The dry-type transformer temperature controller is a new generation of controller designed for the safe operation of dry-type transformers. The controller adopts single-chip microcomputer technology, and uses three platinum thermal resistors embedded in the three-phase winding of the dry-type transformer to detect and display the transformer.
|
|
What should be paid attention to when installing RRKC thermostats - pop-up thermostats
1. The use environment of the sudden jump thermostat should avoid stains and moisture, otherwise it will affect the electrical performance of the product, and the thermostat must be used in a working environment with a relative humidity of ≤ 90% and no contact with corrosive and flammable mediums. For use in wet environments or submerged liquids, the thermostat ...
|
|
Physical and chemical RK C thermostat - dry-type transformer thermostat shows fault handling methods
1. The dry-type transformer thermostat does not appear
Cause of failure: (1) The power supply of the thermostat is not connected; (2) The fuse is blown out.
Solution: (1) Turn on the power supply; (2) Replace the fuse.
2. The dry-type transformer thermostat shows that one or three phases are shining and showing "-OP-"
...
|
|
RK Level Gauge - Introduction to the characteristics of float level gauge
It is suitable for measuring the level and interface of the liquid medium in the container. In addition to on-site instructions, it can also be equipped with remote transmitters, alarm switches, and detection functions.
The indication is novel, the reading is intuitive, eye-catching, and the direction of the observation indicator can be changed according to the user's needs.
Large measuring range ...
|
|
Contact
working hours
