How to set the number of fault retries on Yaskawa servo

1. Use a vacuum cleaner with a plastic nozzle to thoroughly clean the inside and outside of the inverter cabinet to ensure that there is no excessive dust around the equipment. 2. Check the ventilation and lighting equipment of the frequency conversion room to ensure that the ventilation equipment can operate normally. 3. Check that the connection between the cables inside the inverter should be correct and acceptable.

The inverter is composed of a variety of components, some of which will gradually decline and age after the temporary task, which is also an important cause of the failure of the inverter, in order to ensure the temporary normal operation of the equipment, the following devices should be replaced on a regular basis: 2.1 Cooling fan Frequency converters ...

1. Encoder malfunction. When the power is turned on again and this alarm still occurs, it is possible that the servo motor is faulty, and the servo motor is replaced; 2. Encoder malfunction due to noise and other interference. Correct handling of the wiring around the encoder (separating the encoder cable from the servo motor ...

1. Enter the editing mode of Yaskawa robot first 2. Select "Function Effective Setting" for setting 3. Select "Allow" to start the appointment 4. Click Settings to enter "Appointment Activation (Connection)" 5. Set the input signal and output signal you need.

(1) Check and remove the dust and debris on the motor; (2) Check whether the voltage, frequency and power supply voltage and frequency on the nameplate of the motor are consistent with the actual situation, and whether the connection method is correct. (3) Use the insulation resistance meter to measure the phase and phase and phase of the motor winding.

Sina U.S. stock news on the 29th Beijing time Nikkei Chinese Network reported that Japan's Yaskawa Electric will launch an offensive in the European industrial manipulator sales market. In September 2018, Yaskawa Electric will open Europe's first intelligent robot processing plant in South America, with the intention of winning the "European company" as a "European company".

1. The input power supply of the drive drops, resulting in an internal undervoltage alarm. 2. The drive power supply failure causes the safety zone dynamic to detect the undervoltage fault. 3. The servo unit fuse blows. 4. Servo unit failure leads to undervoltage failure. 5. Servo zone dynamic detection circuit fault false alarm ...

PN000 function selection N.0010 (setting value) 0th position: set the direction of rotation of the motor; Set "1" to change the rotation of the motor in reverse. 1st position: Set the control mode to: "1" position control mode. PN200 Command Pulse Input Mode Function Selection N.0101 (Set Value) "1" Positive ...

1. Static test 1. Test the rectifier circuit Find the P and N ends of the DC power supply inside the inverter, adjust the multimeter to the resistance X10 gear, connect the red watch rod to P, and separate the black watch rod to R, S, T. Instead, take the black watch rod ...

Japan's Yaskawa Electric famously created the first all-electric industrial robot, Motoman, in 1977, headquartered in the city of Kita-Kyushu, since its establishment in 1915, has gone from being called "Yaskawa Electric Japan as an automobile manufacturer", "Yaskawa Electric Automation Company of Japan" to "...

Precautions for installing Yaskawa inverter 　　Do not turn on the power supply during wiring operations, otherwise there will be a risk of electric shock. In order to prevent electric shock, please do not operate in the state of removing the inverter cover, otherwise there will be a risk of electric shock. Be sure to ground the ground terminal on the motor side ...

1. First turn off the power - and pull down the power switch. 2. Secondly, use a pen to check the voltage feedback line of the cable behind the base of the robot to see if it is connected or loose. 3. Finally, confirm the abnormality for maintenance. Other error alarm codes can also be used according to the abnormal message under the welder...

There are two scenarios in which the origin of the Yaskawa robot is lost: A. Loss of the origin of individual shafts; B. Lose all axis origins. All axes are created at the same time: When the combination of the robot and the control cabinet is changed, all axes are registered at the origin position at the same time. Each axis is created separately: change the motor or ...

Yaskawa Electric, one of the world's largest manufacturers of industrial robots, announced a 150% year-on-year increase in net profit for the six months ended Sept. 30. The Japan company announced that the company reported a profit for the quarter due to the demand for its industrial robots in China, Japan and United States.

In the case of the growing demand for industrial production, the relatively high cost of manual welding, the small number of welders, and the difficulty of recruiting welders, Yaskawa welding robot provides a perfect solution for welding, and the emergence of industrial robots is undoubtedly a good choice, which has many advantages. Appear...

As a long-standing and reliable supplier of automated metalworking solutions, Yaskawa will be exhibiting at AMB for the first time. Possible applications for the company's Motoman robots include tool handling, machining and stacking workpieces, and machine loading. At booth 6D50 in Hall 6, ...

For the maintenance of Yaskawa robots, maintenance should be carried out before and after each use, check whether there is damage to the outside of the robot, and check whether the robot movement is abnormal. Then be sure to check the battery frequently, and if you find that the battery is not working, you should replace it as soon as possible. The gearbox should be checked frequently to see if there is ...

(1) Determine the equipment in terms of working mode, volume and load type; (2) The equipment can be determined in terms of process, functional standards and control requirements; (3) The system is clarified in terms of I/O interface, communication interface, and assembly mode; (4) Summarize all ...

Yaskawa GP20HL robot is a kind of hollow arm six-axis industrial robot, which is mainly used in automatic production lines such as assembly and material handling, which can not only replace manual work tasks, but also do not affect its operation efficiency. So as its protective product, the Yaskawa GP20HL robot protective suit is ...

1. First of all, connect the terminal block of Yaskawa servo B1B2, in which the B1 terminal receives the power supply and the B2 terminal receives the signal; 2. Then, connect the terminal block of Yaskawa servo B1B2, wherein B1 terminal receives power supply, and B2 terminal receives signal; 3. After the wiring is completed, ...