Yaskawa inverter - how to maintain high-voltage inverter?

　　At 10 a.m. on December 23, 2022, Yaskawa Electric held an online new product launch conference and officially released the next-generation servo products Σ-X series and the new data collection controller YRM-X. Advanced and optimized motion performance and digital solutions starting with servo are the two major features of this new product.

1. Long service life: high-quality dresspack effectively prolongs the service life of the equipment due to the optimization of the sheath material and the expansion device of the dresspack; 2. Easy to replace: In the event of an emergency with internal pipeline damage, the dresspack can be easily replaced without damaging the original sheath and cable joints.

1. Fan With the continuous development of industry, the application of fans is becoming more and more extensive, especially in the chemical, stone and textile industries. However, there is a general problem of over-air volume in the design of the fan, and throttling is generally used when the air volume needs to be adjusted, that is, the damper is adjusted.

1. The correct shielding grounding point is at the reference potential point inside the circuit, which depends on whether the noise source and the receiver are grounded or floating at the same time. 2. Make sure that the shield is grounded at the same point so that the ground current will not flow through the shield. 3. Avoid multiple connections ...

Sina U.S. stock news on the 29th Beijing time Nikkei Chinese Network reported that Japan's Yaskawa Electric will launch an offensive in the European industrial manipulator sales market. In September 2018, Yaskawa Electric will open Europe's first intelligent robot processing plant in South America, with the intention of winning the "European company" as a "European company".

1. When the control power supply is put in, it is caused by the failure of the servo unit circuit board, and the servo unit needs to be replaced. 2. When it occurs in servo ON, then it is caused by the failure of the servo unit circuit board or the short-term motor power line, and the servo unit or motor needs to be replaced.

Q: How often is the robot maintained? A: Generally speaking, the frequency of scheduled maintenance of the robot should be determined on a case-by-case basis. It is generally recommended to carry out a full maintenance every 3-6 months, but for high-intensity and long-working robots, more frequent maintenance may be required.

1. Open the parameter setting interface of the servo drive and find the invert parameter setting option. 2. Set the inversion parameters, including the inversion voltage, inversion speed, etc. Depending on the specific situation, the reversal voltage can be set to -10V and the reversal speed to 1000RPM. 3. After saving the settings ...

1. First of all, connect the terminal block of Yaskawa servo B1B2, in which the B1 terminal receives the power supply and the B2 terminal receives the signal; 2. Then, connect the terminal block of Yaskawa servo B1B2, wherein B1 terminal receives power supply, and B2 terminal receives signal; 3. After the wiring is completed, ...

1. Due to the soft material of the bolt material inside the Yaskawa inverter, if the tool is matched with a large error, it is easy to cause damage to the bolt head, it is recommended to equip the maintenance personnel with special tools of imported or joint venture brands. 2. The electrolytic capacitor and heat sink are made of aluminum alloy.

3. When the oscilloscope checks the current monitoring output of the driver, it is found that it is all noise and cannot be read; Cause of failure: The current monitoring output is not isolated from the AC power supply (transformer). Solution: It can be detected and observed with a DC voltmeter. 4、LE ...

09. Robot oil leakage? Cause: 1. Improper maintenance; 2. Corrosive parts damage, etc. Solution: Check the location of the oil leak and confirm the parts caused by the oil leak. It is possible to accurately determine the parts caused by oil leakage by checking drawings, etc. 10. Robot ...

There are two scenarios in which the origin of the Yaskawa robot is lost: A. Loss of the origin of individual shafts; B. Lose all axis origins. ● All axes are created at the same time: When the combination of the robot and the control cabinet is changed, all axes are registered at the origin position at the same time. ● Each axis is created separately: replace ...

1. Turn on the power switch and compressed air switch of Yaskawa robot. 2. Turn on the main power switch on the Yaskawa robot control cabinet. After the robot completes the self-test, press the servo power button to turn on the servo power supply of the motor. Press the teach-in button (TEACH) on the control cabinet to make the machine ...

Founded in 1989, Yaskawa Motoman is a leading industrial robotics company in the Americas. With more than 400,000 Motoman industrial robots, 15 million servos and 26 million inverter drives installed worldwide, Yaskawa provides automation products and ...

There are three main burning methods for common Yaskawa robot servo motors: overload, phase loss, and short circuit. 1. Overload: Open the servo motor of the industrial robot to observe. The color of the entire winding wire pack has become dark and black, the end strap is cracked, and the serious phase insulation and notch insulation are due to overheating.

(1) The E end of the high-voltage inverter should be connected to the shell of the control cabinet and the motor, and should be connected to the ground, and the grounding resistance should be less than 100Ω, which can absorb surge interference. (2) The input or output of the high-voltage inverter is equipped with an inductive magnetic ring filter. Flat and 3-4 turns, helps to inhibit ...

1. Compressor load Compressors are also widely used loads. Low-pressure compressors are widely used in various industrial sectors, and high-pressure large-capacity compressors are widely used in steel (such as oxygen generators), mines, fertilizers, and ethylene. The use of frequency conversion speed regulation, all bring small starting current, ...

Superior performance "I hope to run the machine at a faster speed and with higher precision" ----∑-V. series servo, the performance of which is the best in the industry. It has the highest amplifier responsiveness in the industry, which greatly shortens the setting time It is only 1/12 of our conventional products ...

1. When the oscilloscope checks the current monitoring output of the driver, it is found that it is all noise and cannot be read; Cause of failure: The current monitoring output is not isolated from the AC power supply (transformer). Solution: It can be detected and observed with a DC voltmeter. 2. Motor ...