KUKA palletizing robots

What is Robotic Welding? Robotic welding is the process of using machines to perform industrial welding tasks. The idea of using welding robots in the robotics industry began in the 1980s, when welding robots found their place on the production line. Nowadays, the role of robotics in welding ...

KUKA Robotics only promises to use industrial robots in accordance with regulations and in a safety-conscious manner when the equipment and skills of the machines are in good condition. Incorrect use can lead to injury and property damage. Not all types of bots have this option. Letters about specific types of bots ...

KUKA Industrial Robots is one of the world's leading manufacturers of industrial robots. More than 10,000 industrial robots are produced every year, and so far, 150,000 have been installed worldwide. Cooka is able to provide standard industrial 6-axis robots from 3KG to 1000KG, as well as some special purpose robots ...

1. Is it that the load data you entered is incorrect? If the load data is too high or too low, and the difference between the load and the practice load is too large, it will cause flutter! 2. Whether there is a large range of turning or posture changes in the running trajectory of the robot ...

l. When planners plan circuit boards, there are unreasonable local planning that are most likely to present problems. 2. The components frequently used in the circuit board are prone to problems. The drive motor and rotating shaft of the industrial circuit board, the switch tube of the switching power supply, the common keys of the operation panel and other components ...

What is tool load data? Tool load data refers to all the loads mounted on the robot flange. It is the mass that is additionally mounted on the robot and moved by the robot with it, and the values that need to be entered are mass, the center of gravity (the point at which the mass is affected by gravity.), the moment of inertia of the mass, and ...

The battery of the KUKA robot is available in two orientations, one on the door and the other under the cooling channel, and is connected to the X305 plug on the control cabinet and protected by F305 fuse. The operating system leaves the factory with the battery plug X305 unplugged from the CCU to ...

Disadvantage 1: When loading software components, the control system is stuck. Causes: The MFC device cannot be initialized, MFC3 is not properly plugged in, and the PCI bus on the motherboard is defective. Solution: Remove the PC card, boot the PC, check the MFC3 slot, and replace the control system PC. ...

First, electrical connection Second, the initial power-on Third, security configuration Fourth, the robot zero point correction Fifth, I/O configuration seline; "> It is necessary to fix the robot before it can be powered on to operate the robot ...

As a branch of industrial robots, KUKA SCARA robots are capable of installation, packaging, labeling, sorting and other processing technologies with their high precision, high cost performance, high flexibility and strong adaptability, helping many manufacturing enterprises to reduce staff and increase efficiency. But with the recent years of high-tech ...

1. Robot welding can improve the output power The six-axis welding robot has a short response time and fast action. The welding speed is 50-160cm/min, which is much higher than that of manual welding (40-60cm/min). The bot does not abort during operation. As long as external hydroelectric conditions are ensured, ...

How to clean up common problems with infrared touch screen 1. Double-click is not very active Open the infrared screen to adjust its activity and reduce the activity. 2. Under what conditions will drift occur Because the operating principle of the infrared screen is to rely on infrared rays...

The gear unit is a very important component of KUKA robot equipment. It has very important features and benefits. The main purpose is to support the mechanical rotating body and reduce the mechanical rotating body. The coefficient of friction is increased, the rotation accuracy is higher, and the service life of the machinery and equipment is longer. So how daily ...

Continuously digitizing construction sites: this is the goal behind the "KUKA NOX" concept study, which was developed by KUKA Corporate Research in collaboration with a Switzerland planning student. Mobile construction robots help to measure and draw on the construction site, making everything important.

1. Active operation method When the KUKA robot is in active operation, it first selects the program that needs to be operated in the manual condition, and then switches the robot to self-power through the key switch, and then starts the robot operation program, so that the robot can reach the BCO safety reference point first, and then ...

When a backup is required: 1. System failure; 2. Hardware collapse. Significance of backup: 1. Save the procedures made at that time; 2. The user can prevent misoperation and deletion of the program; 3. Let the system work from scratch to prevent secondary commissioning or equipment. ...

Introduction to Logic Programming Use input and output in logic programming In order to communicate with the peripherals of the robot control system, digital and analog inputs and outputs can be used. To KUKA ...

1. Connect the oil pump to the discharge hose. 2. Increasing the required amount of oil through the discharge hose. 3. Clean the magnetic plug, check the seal, and replace the damaged magnetic plug. 4. Install the magnetic and tighten it; M ...

The KUKA robot program works in several different ways, which can be selected on the teach pendant. 1. By clicking on the "Program Working Methods" icon, you can check and select different methods Second, the program working methods are respectively [Go], [action], [single ...

According to the use and development needs of KUKA welding robots, traditional welding methods cannot efficiently meet the production needs to a certain extent, and arc welding robot skills are increasingly valued by manufacturers. How to complete mass production efficiently and efficiently with arc welding robots is the most important thing to do.