KUKA palletizing robots increase maintenance efficiency

1. Degrees of freedom and degrees of freedom are the main goals to measure the level of robotics. The so-called degrees of freedom refer to the independent motion of moving parts relative to a fixed coordinate system. Each degree of freedom requires a servo axis to drive, so the higher the number of degrees of freedom, the more chaotic the robot can complete the actions ...

1. How to choose stepper and servo motors? Mainly depends on the specific use situation, in short, it is necessary to determine: the nature of the load (such as horizontal or straight load, etc.), torque, inertia, speed, accuracy, acceleration and deceleration and other requirements, upper control requirements (such as port interface and communication...

The robot control system is an important part of the robot, which is used to control the manipulator to complete specific work tasks, and its basic functions are as follows: 1. Recall function: store the order of work, the way of movement, the way of movement ...

If the initial adjustment is lost (e.g. after a motor replacement or a bump), the initial adjustment is reverted. Since the learned error persists after the adjustment is lost, the KUKA robot calculates the initial adjustment. Before checking an axis, it is necessary to complete the ...

1. Fault phenomenon: KUKA Robot Teach Pendant KRC4 The screen is out of order, and the mouse arrows do not move when touching the screen, and there is no change in orientation. 2. Causes: There are many reasons for the formation of this phenomenon.

1) Rapidity. The time from obtaining the command signal to the completion of the required working state of the motor should be short. The shorter the time to respond to the command signal, the higher the sensitivity of the electric servo system, and the better the fast response function.

There is no program display when the KUKA robot is restarted, that is, the gun cleaning program has been deleted, maybe the name of the program has been changed. Of course, KUKA robots have programs, KUKA robot bodies, handheld teaching programmers and control cabinets, there are all kinds of circuit boards, circuit boards are required to program ...

Robots at the same station, in the process of operation, need to enter the same area, but there is no strict restriction on the order of entry, a robot (Master) has the right of priority, that is, the robot first enters the dry and area, and another robot (Slave) after the operation is completed...

There is a program called BAS.SRC under the R1System in the KUKA robot program directory, which is mainly used to set the number of parameters related to the robot motion, such as coordinate system, velocity, acceleration, etc. One. Online forms Let's take a look at how to use the commonly used online form.

1.Japan The internal gear error of the RV reducer affects the gear manufacturing process, and the tooth shape error, base joint deviation, tooth direction error and gear ring radial runout error are the main errors that lead to the transmission noise of the planetary Japan RV reducer. It is also a problem point to control the transmission power of the planetary Japan RV reducer. Now with ...

In recent years, KUKA has made a qualitative leap forward in robot skills, and the robot's performance has been continuously improved and adaptable. In order to ensure the service life of KUKA robots, KUKA robot dresspacks are widely used. With the continuous improvement of the robot system, the variety of pipeline packs is also increasing.

According to the application status and development needs of the welding technology of KUKA welding robots, the traditional welding methods must not be able to meet the production needs to a certain extent, and the arc welding robot technology has been paid more and more attention by manufacturers. How to complete the batch production of arc welding robots, is the current arc welding machine...

1. Program control system: apply a certain control effect to each degree of freedom, and the robot can complete the required space orbit. 2. Adaptive control system: when the external conditions change, in order to ensure the required quality or in order to improve the control with the accumulation of experience...

1. It is necessary to conduct teaching assignments Before the robot performs active welding, it is necessary for the operator to teach the robot the track of the welding gun and set the welding conditions. Because it is necessary to teach, the robot does not weld to a wide range of products produced in a small number of products. 2. There must be ...

When a backup is required: 1. System failure; 2. Hardware collapse. Significance of backup: 1. Save the procedures made at that time; 2. The user can prevent misoperation and deletion of the program; 3. Let the system work from scratch to prevent secondary commissioning or equipment. ...

One. Outline: Those who have used KUKA robots should know that to indicate the orientation of a robot's Cartesian coordinate system, data of type FRAME/POS/E3POS/E6POS type will be used, during which the following period: -X/Y/Z: indicates the rectilinear coordinates of the Cartesian coordinate system; -A/B/C ...

Definition: Industrial robot is widely used in the industrial field of multi-joint manipulator or multi-degree of freedom machine device, with a certain degree of automaticity, can rely on its own power and control ability to achieve a variety of industrial processing and production functions. Industrial robots are widely used in electronics, logistics, chemical ...

The 21st China International Industry Fair (CIIF) will be held at the National Convention and Exhibition Center (Shanghai) from September 17 to 21, 2019. At booth E025 in hall 8.1H, KUKA will bring a series of digital and intelligent robot products and application processing plans to the show! All along, KU ...

The cost of the global robot is mainly composed of: about 35% of the reducer, about 20% of the servo machine, about 15% of the control system, and only about 15% of the mechanical processing of the robot body. The world's high-end robots are mainly controlled by a small number of international robot companies such as ABB, Fanuc and Kuka, and they ...

At present, the use of robots in machine tools by domestic enterprises is still in its infancy, and many theoretical and practical problems have not been fully understood and handled. For example, the most common form of use is still a simple combination of machine tools and robots, each using a set of control systems. To get the most out of the machine ...