The EhaveCM350AR is a fully digital inverter melting multi-functional industrial heavy-duty Megmeet welding machine launched by Megmeet for global metalworking manufacturing. It brings customers higher quality and higher efficiency welding experience and value with excellent arc characteristics, reliability and high efficiency, and helps customers ...

1. The main welding machines used in industrial and mining enterprises are: AC arc welding machine, DC electric welding machine, argon arc welding machine, carbon dioxide maintenance welding machine, butt welding machine, spot welding machine, submerged arc welding machine, high-frequency welding machine, bright butt welding machine, pressure welding machine, butt welding machine and laser welding machine. Communication welders and DC welders should ...

What aspects should be paid attention to in the application and protection of AC arc welding machine: (1) It should be used according to the additional welding current and load continuation rate of the welding machine, and should not be overloaded. (2) The welding machine is not allowed to be short-circuited for a long time. (3) The regulating current should be operated at no load. （4） ...

1. The circuit board inside the inverter belongs to precision electronic components, which needs to be moisture-proof and dust-proof, and the temperature and humidity are not too high, and cannot be installed on the bare wall, so the inverter should be installed in the middle of the control cabinet; The inverter should be installed vertically, and the installation should be avoided directly above and below ...

1. Fault phenomenon: light voltage abnormal indicator Cause: Due to the slow start-up action, the switch contact is not synchronized. Solution: You can turn the device off and on again. 2. Fault phenomenon: the fan does not rotate, and the abnormal voltage indicator light is lit together Causes ...

1. The Megmeet rectifier module is damaged It is usually caused by grid voltage or internal short circuit. In the case of sweeping the internal short circuit, the rectifier bridge is replaced. When dealing with faults on site, we should focus on checking the status of the user's power grid. Such as the power grid voltage, whether there is an electric welding machine, etc.

1) Hand arc welding (STICK) Shielded Arc Welding (abbreviated SMAW) in English, The principle is: the arc occurs between the coating electrode and the base metal, and the welding method of arc thermal ablation electrode and base metal is used. The outer layer of the electrode is covered with solder, which is dissipated in case of heat.

On September 24, the 2021 Zhongguancun Forum, co-sponsored by the Ministry of Science and Technology of China, the Chinese Academy of Sciences, the China Association for Science and Technology, and the Beijing Municipal People's Government, officially opened in Beijing. As one of the main agendas of the forum, the Zhongguancun International Technology Exchange Conference closely follows the "smart· healthy· carbon neutrality...

1. External equipment failure. Such faults come from external devices such as various sensors, switches, actuators, and loads. The failure of this part of the equipment will directly affect the control function of the system. This type of failure is usually caused by the quality and longevity of the equipment itself. 2. System failure ...

Transportation power, urban rail responsibility. With the vigorous development of emerging technologies such as 5G, cloud computing, big data, and artificial intelligence, more innovative technologies are accelerating the empowerment of urban rail transit, and smart urban rail is ushering in a "golden age" of development. As a deep cultivator in the field of smart urban rail, Hollysys adheres to technological innovation.

Carbon dioxide gas shielded welding (referred to as CO2 welding) is the use of CO2 gas as the maintenance medium, during welding, CO2 gas is sprayed out through the nozzle of the welding gun, along the perimeter of the welding wire, forming a gas maintenance layer around the arc, mechanically isolating the welding arc and the molten pool from the air, and then avoiding ...

1) Hand arc welding (STICK) Shielded Arc Welding (abbreviated SMAW) in English, The principle is: the welding method of generating an electric arc between the coating electrode and the base metal, and using the arc heat to melt the electrode and the base metal. The outer layer of the electrode is covered with solder, and it melts when heated.

Safety operation procedures for spot welding machines: 1. Before operation, the oil stain of the upper and lower electrodes should be removed. After power-on, the body shell should be free of leakage. 2. Before starting, the steering switch of the control line and the small switch of welding current should be connected, the number of poles should be adjusted, and then the water source and gas source should be connected.

3) Tungsten argon arc welding (TIG) Non-melting electrode gas arc welding, TIG welding, English is Tungsten Inert Gas (abbreviated TIG), also known as Gas Tungsten Arc Welding (abbreviated GTAW) The principle is: TIG welding is in argon and other inert gases.

5) PLASMA The principle of plasma cutting is: arc discharge between the base metal (including the nozzle in the cutting torch) and the electric in the cutting torch, and use the discharge heat energy to make the compressed gas produce a high-temperature and high-speed plasma arc to fuse the cutting method of the base metal. The small hole of the nozzle ...

The butt welding machine should be settled indoors, and should have a reliable grounding or zero connection, when a plurality of butt welding machines are connected to each other, the distance from each other shall not be less than 3m, and they should be connected to different corresponding power grids, and should have their own knife switches. Before welding, the pressure of the butt welder should be checked and determined.

(1) The energy density is highly concentrated, the heating and cooling speed is extremely fast during welding, the heat affected zone is small, and the welding stress and deformation are very small; (2) Non-touch processing, no external force on the weldment, suitable for welding parts that are difficult to touch; (3) The laser can be transmitted through the optical incoming ...

1. The arc is stable in the field of full current, the spatter is small, and the same welding machine is not only suitable for small current base welding, but also suitable for high current and high deposition rate work 2. Arc concentration and strong penetration. With the same penetration depth, the heat input is reduced by more than 20% compared with other gas shielded welding machines, and the thermal deformation ...

1. CPU abnormality: When the CPU is abnormally alarmed, check the device connected to the internal line of the CPU unit. The specific method is to replace the units that may cause failures in turn, find out the faulty units, and deal with them accordingly. 2. Memory abnormality: When the memory is abnormal alarm, if it is a program ...

Advantages of resistance welding: 1。 When a nugget is formed, it is always surrounded by a ring of plastic, the molten metal is isolated from the air, and the metallurgical process is simple 2。 The heating time is short, the heat is concentrated, the heat affected zone is small, and the deformation and stress are small. In general, there is no need to arrange calibration and heat after welding.

When the oscilloscope looks at the current monitoring output of the driver, it is all noisy and cannot be read Cause: The current monitoring output is not blocked from the AC power supply (transformer). Solution: You can use a DC voltmeter to detect and investigate. Servo motor high-speed rotation ...