Buke servo motor - AC motor speed regulation method

1. When the motor rotates, the LED light flashes (1) Cause of failure: HALL phase error. Solution: Check whether the motor phase setting switch is correct (2) Fault cause: HALL sensor failure, treatment method: When the motor rotates, detect the voltage of HalA, HalB, HalC ...

On December 10th, the "2020 Buke - IoT Machine Internet of Things Solution Seminar" was held in Wenzhou Ruian, with more than 60 company leaders including Tang Dong, chairman of Buke Co., Ltd., Wang Gang, sales executive, and Ouyang Yunsheng, director of HMI products, attended by more than 60 company leaders, as well as new/old agents and terminals from Wenzhou.

Material metering The measurement of powdery materials is commonly used in the way of screw measurement. The purpose of measurement is achieved by the number of turns of the screw rotation. In order to improve the accuracy of measurement, the speed of the screw is required to be adjustable, and the position positioning is accurate.

B3: The base has feet. The end cap has no flange. Mounted on foundation members. B35: The frame has feet. Flange on the end cap. The flange has through holes. It is installed on the foundation member by a foot and attached to the flange mounting. B34: The frame has feet. The end cap has a flange and a screw on the flange.

1. Check the servo motor to ensure that there is no fatal damage outside; 2. Check the fixed parts of the servo motor to ensure that the connection is strong; 3. Check the output shaft of the servo motor to ensure the rotation and circulation; 4. Check the encoder connection line of the servo motor and the ...

Since the new crown epidemic, the rapid growth of e-commerce has made the overall scale of China's express delivery industry grow rapidly, according to incomplete statistics, the business volume in 2020 has exceeded 80 billion pieces. Due to the growth of express delivery business volume, the automatic sorting efficiency of express delivery and parcels is becoming higher and higher.

6. When the motor is unloaded and overloaded, the ammeter pointer is unstable and swings 1. Cause of failure (1) The cage rotor guide bar is welded or broken; (2) Winding rotor fault (one-phase break) or poor contact of brushes and collector ring short-circuit devices. 2. Troubleshooting ...

Hmi: Human-machine interface refers to the field in which man and machine contact or interact with each other in information exchange and function, or the human-machine interface mentioned in the interface. Information exchange, functional contact or mutual influence, refers to the hard contact and soft contact between man and machine, this combination includes not only dots and lines...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

· They offer significant cost-effectiveness · They provide smoother operation · they are very efficient and tend to reduce energy costs · can optimize thermal management by embedding the motor into the machine · They offer improved servo performance and therefore improved production ...

1. Check whether the joints of each connecting line are loose; 2. Check whether there is a conflict between the serial port and the abort number, and if there is a conflict, the resources should be adjusted to circumvent the conflict. Then check whether there are gaps in the surface layer of the human-machine interface, and if there are gaps, they should be replaced immediately. It also needs to be inspected ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke. 1. Cause of failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) Control ...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

1. Remove the damaged encoder 2. Install a new encoder on the damaged motor 3. Find the Z signal and two power cords according to the figure, the general power supply is 5V. 4. Prepare a 24V and 5V output switching power supply with a slightly modified open circuit alarm and ...

1. The working principle of servo motor encoder It is a rotary sensor that converts rotational displacement into a series of digital pulse signals that can be used to control angular displacement, and can also be used to measure linear displacement if the encoder is combined with a gear bar or spiral screw. ...

1. Wide range of speed regulation 2. High positioning accuracy 3. There is sufficient transmission rigidity and high speed stability 4. Fast response, no overshoot In order to ensure productivity and processing quality, in addition to high positioning accuracy, it is also required to have a good and fast response ...

1. Bearing failure is one of the most common motor failures. As the most important consumable part in servo motors, more than half of the failures of servo motors are usually caused by bearing problems. Its specific manifestations are varied, from jitter and abnormal noise when the motor rotates to the jamming of the motor shaft. Value...

Drive Alarm 0006 Please troubleshoot in the following order: 1. Is the motor model correctly configured? 2. Is the motor encoder cable firmly connected? 3. If the above two points are correct, please replace the motor or driver for cross-comparison and troubleshooting. As mentioned above ...

What are the power requirements for hardware setup 1, ED100 and ED200? The logic power supply of the Kinco servo is DC24V (scale is 18V-30V), not less than 1A (if the boundary says OUT and Brake output, it is not less than 2A); The power supply of ED100 is DC24V-DC70V, and the power supply requirements of ED200 and ED216 are D...

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...