Buke servo motor - the structure and installation type of Y series three-phase asynchronous motor

1. Remove the damaged encoder 2. Install a new encoder on the damaged motor 3. Find the Z signal and two power cords according to the figure, the general power supply is 5V. 4. Prepare a 24V and 5V output switching power supply with a slightly modified open circuit alarm and ...

Recently, the Ministry of Industry and Information Technology of the People's Republic of China has completed the review of the fourth batch of specialized, special and new "little giant" enterprise cultivation, and publicized the list of enterprises that have passed the review.

1. When the motor rotates, the LED light flashes (1) Cause of failure: HALL phase error. Solution: Check whether the motor phase setting switch is correct (2) Fault cause: HALL sensor failure, treatment method: When the motor rotates, detect the voltage of HalA, HalB, HalC ...

1. The basic functions and selection indicators of human-machine interface products Basic Functions: Display of equipment working status, such as indicator lights, buttons, text, graphics, curves, etc.; Data and text input operations, printouts; Production recipe storage, equipment production data ...

1. Adopt a power supply with excellent performance to suppress the interference introduced by the power grid. For the power supply supplied by the PLC controller, the non-power line power supply should be adopted, and the special line power supply should be used directly from the main bus of the low-voltage distribution room. Isolation transformers are selected, and the transformer capacity should be larger than the actual needs.

(1) Wiring should be done with the power supply OFF, and if the output line is in contact with the power supply when the power is turned on, the output circuit may be damaged. (2) If the wiring is incorrect, the internal circuit may be damaged, so pay full attention to the polarity of the power supply when wiring. (3) If and high-voltage lines, ...

1. In the daily inspection, the lubrication system, appearance, temperature, noise, vibration and abnormal phenomena are mainly checked, and the ventilation and cooling system, sliding friction and fastening of each component are also checked, and the inspection records are carefully made. 2. During the monthly or regular inspection, the main inspection ...

The servo motor can control the speed, the position accuracy is very accurate, and the voltage signal can be converted into torque and speed to drive the control object. The rotor speed of the servo motor is controlled by the input signal, and can respond quickly, in the automatic control system, used as an actuator, and has an electromechanical time constant...

A servo motor encoder failure means that the encoder component is faulty, preventing it from generating and outputting the correct waveform. In this case, the method of repair is to replace the encoder or repair its internal parts. 1. Encoder connection line failure: this kind of failure has the highest probability of repair...

1) The working status of the equipment is displayed; 2) Data and text input operation, printout; 3) Production formula storage, equipment production data recording; 4) simple logical and numerical operations; 5) It can be connected to a variety of industrial control equipment networking. ...

1. Comparison link The comparison link is to compare the input command signal with the feedback signal of the system to obtain the deviation signal between the output and the input, which is usually implemented by a special circuit or computer. 2. a controller The controller is usually a computer or PI...

Cause of the failure 1) The sound wave reflection stripes on the four periphery of the surface sound wave touch screen are seriously dusty or scale, resulting in the touch screen not working. 2) The touch screen is malfunctioning. 3) The touch screen control card is faulty. 4) The touch screen signal line is faulty ...

1. The motor cannot rotate after being energized, but there is no abnormal noise, no peculiar smell and smoke. 1. Cause of failure (1) The power supply is not connected (at least two phases are not connected); (2) Fuse blowing (at least two-phase blowing); (3) The overcurrent relay is adjusted too small; (4) Control ...

1. For new or long-term out-of-service motors, the insulation resistance between the windings and the windings to the ground should be checked before use. Usually for motors below 500V, 500V insulation resistance meter is used; 1000V insulation resistance meter for 500-1000V motors; 2500V insulation resistance meter for motors above 1000V. Insulated ...

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

1:11 alarm, control the power supply undervoltage, control the power inverter on P. The voltage between N is lower than the specified value. There are defects in the internal circuitry of the driver, etc. 2:12 alarm, control power supply overvoltage, control power inverter on P. N voltage exceeds the specified value, ...

1. If the servo motor is an AC motor, it is a DC inverter air conditioner for speed regulation; If the servo motor is a DC brushless DC motor, it is the DC power supply DC transformer speed regulation; All servo motors can be used as "PLC motor speed regulating power supply circuit servo motor". 2、 ...

Frameless torque motor is a new type of direct-drive torque motor, which is designed for applications that require small size, light weight, low inertia, low cogging torque, and high power. High reliability - no mechanical transmission, long life and easy installation. Serialized products are not limited to the following types ...

Mechanical 1. Bearing The bearing clearance on the lead screw housing is too large after wear, or the bearing roller elements and cages are severely worn due to the lack of grease in the bearing, resulting in excessive loads. After bearing wear, the clearance is too large, which will cause the coaxiality error between the center of the motor rotor and the center of the lead screw.

1. Communication cannot be connected. 2. The interference in the process of data transmission will increase (sometimes it is not bad, but the connection between the host computer and the servo is incorrect, or there is a falling off, which is a very common problem). 3. The motor will run, but it will not work according to the instructions given by the servo ...