1. Clarification of the function of the control panel
1. FUN button; Press the FUN button to enter the settings menu F00;
2. Press and hold the up or down button to scroll to the code you need to set;
3. At this moment, press the FUN button to confirm, and adjust the entry parameters to the required value;
4. After the adjustment, press the WR storage button, when the panel displays E2-or YE5-, the new value is useful to write, and the new input value is invalid when E┲┲--is displayed;
5. After the setting is completed, press the FUN key to return to the setting code, press the down button or up key to F00, and press the FUN button to return to the initial menu;
Second, the function of the code is clarified
1. F00 main setting/observation window;
2. The lower limit of F01 input frequency is 0.00-40.00HZ; The factory value is 0HZ, and the open loop is limited to a small value;
3. The upper limit of F02 input frequency is 20.00-600.0HZ; The factory value is 50.0HZ.
4. F03 fundamental frequency 26.0-600.0HZ; The factory value is 50.0HZ.
5, F04 instruction form 0-keyboard; 1-terminal positive/rotary form; 2 - spare; 3-terminal self-adhering form; 4-RS485 serial port communication form; The factory value is set to 0; Self-adherence form requires external auxiliary terminal (X4) cooperation, see F56;
6, F05 main setting source selection 0-keyboard number given, 1-internal multi-stage speed given, 2-terminal imitation voltage VG given (0-10V), 3-terminal imitation current Ig (0-20mA) given, 4-terminal imitation current Ig (4-20mA) given, 5-electric potentiometer given, related parameters F54, 6-RS48 serial interface given, 7-composite multi-stage speed form 0.10-999.9sec, operation instruction and direction by F04 resolution; The ex-factory value is 0;
7. F06 *** acceleration time 0.10 - 999.9sec, factory value of 5.0sec;△*** acceleration and deceleration parameters and the second acceleration and deceleration parameters are switched by terminal X3 selection (see F55);
8. F07*** deceleration time 0.10-999.9sec, factory value is 5.0sec;△*** acceleration and deceleration parameters and the second acceleration and deceleration parameters are switched by terminal X3 selection (see F55);
9. F08 arc time 0.0-50HZ, 0.0sec; △*** The acceleration and deceleration parameters and the second acceleration and deceleration parameters are switched by terminal X3 (see F55);
10. F09 second acceleration time 0.10-999.9sec; 5.0sec； △*** The acceleration and deceleration parameters and the second acceleration and deceleration parameters are switched by terminal X3 (see F55);
11. The second deceleration time of F10 is 0.10-999.9sec; 5.0sec； △*** The acceleration and deceleration parameters and the second acceleration and deceleration parameters are switched by terminal X3 (see F55);
12. F11 standby 0.0-50.0sec; 0.0sec；
13. F12 standby 0.0-50.0sec; 0.0sec；
14, F13 shutdown form 0-soft abort; 1- Immediate abort;
15, F14 re-start form 0 - to stop the restart, 1 - to recall the frequency and phase tracking and then start, 2 - to re-start according to the speed measurement frequency of the tracking, 3 - according to the convention of power-on delay and then start; The ex-factory value is 0; In the process of stalking, the operation signal is exempted, and the stalking is immediately suspended, which has nothing to do with F13 at the moment; When the stalking is useful, it will negligently activate the DC active; The speed measurement form must be installed with an encoder;
16. The F15 speed tracking conditioning time is 100-9999ms, and the ex-factory value is 1000ms;
17. F16 speed tracking current constraint 30.0-300.0%; Factory value: 100.0%;
18. F17 active stalking conditioning time is 5.0sec-600.0sec, the factory value is 10.0sec, and 600.0sec is equivalent to not exempting stalking;
19. F18 starting frequency 0-30HZ; Factory value 0.00HZ, given frequency below this frequency, the system insists on the machine and does not remember the keyboard instructions;
20, F19 DC braking 0 - no DC braking; 1-DC braking after starting; 2-DC braking after deceleration abort; 3-For starting/aborting uniform DC braking; The ex-factory value is 0; Start DC braking DCb-, stop DC braking shows dcb, and the braking frequency is lower than the initial frequency, which is equivalent to DC braking invalidity
|
More on that
|
Difference Between Soft Starter and Inverter – Reynolds
Soft starters and frequency converters are two completely different products. The inverter is used in the local area where speed regulation is required, and its output not only changes the voltage but also changes the frequency at the same time; A soft starter is actually a voltage regulator, which is used when starting a motor, and the output only changes the voltage and does not change the frequency. Change...
|
|
The heat dissipation method of the switching power supply
1. Transfer heat pipes for heat dissipation.
In many applications, heat generated from the base steel plate of the power module is transferred through the heat transfer components to the distant surface of the heat pipe. In this way, the temperature of the base steel plate of the power module will be equal to the temperature of the heat pipe heat dissipation surface, the temperature of the heat transfer parts, and the temperature of the two contact ...
|
|
The difference between the voltage type and the current type of inverter - Reynolds
Energy storage elements are different, the voltage type energy storage element is a capacitor, and the current type is an inductor. In fact, the general inverter uses power electronic circuits, which is a process of communication to DC - DC energy storage - DC to communication. It is also often said that the rectifier link --〉 energy storage link --〉 inverter ring ...
|
|
The difference between inverter motor and ordinary motor - Reynolds
1. The heat dissipation system is different: Generally, the cooling fan in the fan is in the same line as the fan movement, while the two are separated in the inverter motor. Therefore, when the frequency conversion of the fan is too low, it may burn out due to overheating.
2. Frequency conversion ...
|
|
Inverter leakage solution - Reynolds
1. The cause of the leakage problem
Some sites use frequency converters to control the motor, which will present the problem of leakage, and the leakage voltage ranges from tens of volts to 200 volts. In view of this problem, the reasons for this shortcoming are theoretically expounded and stated as follows.
Depend on...
|
|
Elimination of inverter harmonics method – Reynolds
a. Add the internal impedance of the power supply of the inverterIn general, the internal impedance of the power supply equipment can play a role in buffering the reactive power of the DC filter capacitor of the inverter. This internal impedance is the short-circuit impedance of the transformer. When the power supply capacity is smaller than the inverter capacity, the internal impedance value is relatively large.
|
|
The difference between "braking" and "parking" of the inverter - Reynolds
There are two types of inverter parking.
One form is called "free parking". As the name suggests, it is to quickly "power off" the motor, so that the motor can slide and park by its own inertial force (OFF2 parking);
The other form is called "brake parking". So this "brake parking ...
|
|
Precautions for low-temperature operation of VFD
1. VFD should be operated in an environment above minus 10°C as much as possible, and it is best to operate indoors.
2. When the VFD is started and stopped, try to start and stop with the VFD itself, do not close the power supply, and keep your VFD in a power-on state.
3. Give VFD l ...
|
|
The inverter prepares the braking resistance factor – Reynolds
The preparation of the braking resistor of the inverter is mainly to consume part of the energy on the DC bus capacitor through the braking resistor to avoid the capacitor voltage being too high. Theoretically, if the capacitor stores a large amount of energy, it can be used to release it to drive the motor and avoid energy waste. However, the capacitance of the capacitor is ...
|
|
PLC and inverter communication mode
1. The switching signal of PLC controls the inverter
The PLC can control the start, stop and reset of the inverter through the program; It can also control different combinations of high-speed, medium-speed and low-speed terminals of the inverter to achieve multi-stage speed operation. However, because it is controlled by switching ...
|
|
Reynolds inverter parameter problem
1. What are the factory recovery parameters of Reynolds inverter?
N600 = 100 (often press the WR button for 3-5 seconds), it is necessary to be in the shutdown state to be effective.
2. In the parameters of the N308 motor of the inverter, is the [motor leakage inductance reactance] specified sub-leakage inductance or rotor leakage inductance react?
Decide...
|
|
The lightning protection method of Reynolds inverter
The lightning protection measures of the inverter equipment are another important peripheral measure to ensure the safe operation of the inverter, especially in the area where lightning is active or in the lively season, this problem is particularly important.
Today's inverter products are generally equipped with lightning ...
|
|
Characteristics of isolation transformer at the input end of AC power supply - Reynolds
a。 When the third harmonic and disturbance signals are severe, a barrier transformer can be used to eliminate the third harmonic and disturbance signals.
b。 The use of barrier transformers can generate new neutrals and avoid the abnormal operation of equipment due to defective neutrals in the grid.
...
|
|
Reynolds-5G empowers the paper industry to improve quality and efficiency of the industrial IoT control system
From September 23rd to September 25th, 2020, the 2020 China International Paper Technology Exhibition was held in Hall D1 of Suzhou International Expo Center.
|
|
Introduction to soft starters and their relationship with frequency converters - Reynolds
When the high-power motor starts, the current is large, which will cause the grid voltage to be seriously shaken, in order to deal with this problem, the general requirements for speed regulation are not high, and the soft engine can be used to reduce the voltage and start. However, the drop in the starting current when the step-down is started will also make the starting torque drop significantly.
|
|
Inverter composition and various functions - Reynolds
Rectifier circuit: rectify 50HZ communication power into direct current.
Frequency conversion circuit: The rectified direct current is inverted into a variable frequency communication current.
Control part: control the frequency of communication electricity output by the inverter circuit.
Maintenance circuit: maintenance and blockage of overcurrent and phase loss ...
|
|
Inverter dust handling – Reynolds inverters
1. Plan a special inverter room: When the power of the inverter used is large or the number is large, a special inverter room can be planned. The doors, windows and cable holes in the room should be sealed to prevent dust from entering; It is necessary to plan air filtration equipment and circulation channels to adhere to the normal circulation of indoor air ...
|
|
Reynolds assisted Sinopec Weirong shale gas project
With the rapid development of China's national economy, the supply and demand situation of oil and gas resources is becoming increasingly severe, and the import of oil and gas is increasing year by year, so it is urgent to expand the field of domestic oil and gas exploration and development. Strengthening the exploration and development of shale gas resources can make up for the lack of conventional oil and gas resources and promote the sustainability of the oil and gas industry.
|
|
Reynolds soft starter fault code and fault handling
Reynolds soft starter fault code
Instantaneous stop -F 01 Instantaneous stop terminal 7 to terminal 10 open
TOO LONG STARTING TIME -F 02 STARTING TIME IS TOO LOW AND THE STARTING TIME IS TOO LONG (GREATER THAN 60S)
Overheating -F 03 Start too often, reduce the number of starts
Input out of phase -F 04 ...
|
|
Frequency converters need to be replaced regularly – Reynolds
The inverter is composed of many electronic parts, such as semiconductor components, etc., in the application and protection involves the replacement of a related component, because of the composition or physical characteristics of the inverter, it will deteriorate in a certain period of time, which will reduce the characteristics of the inverter, and even ...
|
|
Contact
working hours
