Software options for real-time movement of KUKA robots

1) Comfort degree: This is an important goal that reflects the flexibility of the robot. Generally speaking, it is possible to reach 3 degrees of freedom in the robot work space, but the welding must not only reach a certain direction in the space, but also ensure the spatial attitude of the welding (cutting things or welding tongs). Thus...

In the foreign capital to speed up the layout of China's parallel robot shopping mall, the domestic market is not to be outdone, with the advantage of cost performance and the development of new use areas, domestic parallel robots or will take the lead in opening the game with foreign capital. Now, most of the world's domestic parallel robots ...

Once the phenomenon of the robot servo motor drive burning MOS tube is started, the external stable wire of the drive will be burned, and the equipment cannot be operated. When the repairer checked, he found that a power tube had been damaged, but because there was no material, he couldn't figure out the effect of the tube.

First, a single robot stamping and unloading: the robot will transfer the plate data from the palletizing table to the positioning table, and then transfer it to the stamping die for stamping after positioning, and after the stamping is completed, the data will be brought into the palletizing table through the robot, and the single pressure robot will be automatically loaded and unloaded. Second, robot stamping ...

(1) Provide voltage and have the function of power distribution (2) The decombiner (SIL2) technology is used to collect the orientation information of the eight motors for orientation feedback (3) Obtain the real-time temperature of the motor (PTC) （4） ...

Industrial robots are the star products of industrial automation, and the 30 billion ontology space is expected to leverage trillions of automation to transform shopping malls. The body space is about 30 billion yuan: the essence of automation is the automation of the process, and the ultimate policy is to improve the total factor yield. Multi-axis industrial robot is an automated ...

The resolution of an industrial robot generally refers to the minimum positioning capability of the robot's end actuator in three spatial directions, usually expressed in millimeters or microns. It reflects the accuracy requirements of the industrial robot control system for the orientation and movement of the robot, and is an important measure of the functional advantages and disadvantages of industrial robots.

Fault Symptom: After the robot is turned on, the teach pendant shows KSS15101 fault code (the safety device is wrong in 5 safety nodes from 0 to 4 channels), and the robot cannot be put into operation normally. Fault Detection: First inspect the site ...

The servo manipulator controls the manipulator's actions through servo motors and servo drives. The servo manipulator has higher control accuracy than the frequency conversion manipulator and is expensive. Inverter manipulator is an automatic production equipment that can imitate some functions of the upper limbs of the human body, and can be automatically controlled according to predetermined requirements.

1. Before replacing the KVGA, the following preparations must be made: 1. The robot control system must be permanently shut down and protected against unauthorized accidental restarts. 2. The buffer is closed. 3. Put the feeder cable in a powerless condition. ...

As a branch of industrial robots, KUKA SCARA robots are capable of installation, packaging, labeling, sorting and other processing technologies with their high precision, high cost performance, high flexibility and strong adaptability, helping many manufacturing enterprises to reduce staff and increase efficiency. But with the recent years of high-tech ...

1. Place the nut Clamp the quad or hex nut and place it in the fixture 2. Thread sizing Grab the screw and assist it to complete the "180-degree turn" action; Apply an appropriate amount of sealant to the thread on its underside ...

The transfer robot is a manipulator in practical work, and the manipulator is developed because its positive role is increasingly known: First, it can partially replace manual operation; Second, it can follow the requirements of the production process, follow the certain procedures, time...

First, welding robot inspection and protection 1. Wire feeding arrangement. Including whether the wire feeding force is normal, whether the wire feeding tube is damaged, and whether there is an abnormal alarm. 2. Is the airflow normal? 3. Is the torch safety protection system normal? (It is forbidden to close the welding torch safety protection ...

Most of the fieldbus communication failures of KUKA robots are divided into the following five situations. Fault 1: Unable to communicate through the diagnostic program interface. Causes of failures: data cables, peripherals, fieldbus cards, etc.

1. Enter the program in the form of the teach pendant T1, click on the lower left corner: Instruction - Logic, and you will see the commonly used logic instructions such as WAIT, WAITFOR, and OUT. 2. Select WAIT. The lower end of the interface *** presents the WAIT Time port sec .

The maintenance content of the robot is mainly to replace the lubricating oil of the six shaft reducers and the lubricating oil of the J4 shaft gear shaft, the replacement of wearing parts, the inspection of the operation status of each module in the control cabinet, and the inspection of the wear status of each cable in the control cabinet. If the grease is not replaced for a long time, the six axes of the robot will be formed.

1. Robot selection An industrial robot is a complex system, including manipulators, control systems, programmers and other software and accessories. Before use, it is necessary to select according to the actual production requirements of the enterprise and choose the products suitable for their own production line. Selected Guideline Packet ...

A lightweight cobot is an industrial robot with a flat, small touchscreen user interface that allows the user to control the robotic arm by instructing the movements on the screen. Perhaps, by holding the robotic arm easily, the desired path of movement is displayed. The interface fits most industrial sensors and ...

1. Select Put into operation > Measure > Stuff > XYZ 4 points from the main menu. 2. Give a number and a name for the thing to be measured. I admit it with the continuation key. 3. Use TCP to move to any reference point. Click Measure. Click Yes to reply to the security question ...