Range of sensor applications – Autonex

1. Errors in improper introduction of devices In other words, the thermocouple should not be installed too close to the door and the heating place, and the penetration depth should be at least 8-10 times the diameter of the maintenance tube; Maintenance of thermocouples ...

A gas sensor is a converter that converts the volume fraction of a gas into an electrical signal. We will inevitably encounter some problems when using gas sensors, and we have analyzed them as follows: 1. How long does it take for the gas sensor to be used and then calibrated again: the initial calibration ...

Humidity sensors are divided into resistive and capacitive types, and the basic form of the product is to coat the substrate with moisture-sensitive materials to form a moisture-sensitive film. After the water vapor in the air is adsorbed on the moisture-sensitive material, the impedance and dielectric constant of the element are greatly changed, so as to make a moisture-sensitive element. ...

1. Avoid strong light sources Photoelectric sensors can generally operate stably when the ambient illumination is high. However, avoid facing the optical axis of the sensor with strong light sources such as sunlight and incandescent lamps. When the angle of the optical axis of the sensor (light receiver) and the strong light source cannot be changed, the sensor can be surrounded by ...

First, the difference in working principle Photoelectric sensors are controlled by converting changes in light intensity into changes in electrical signals. The laser sensor first emits a laser pulse by aligning it with a laser emitting diode. After being reflected, the laser light is scattered in all directions. Partially scattered light returns to ...

In the rotary power system, the most frequently involved parameter: rotational torque, in order to detect the rotational torque, the traditional use of torsion angle phase difference sensors. The more mature detection method of torque testing is strain electrical testing skills. It has high precision, fast frequency response, good reliability, long life, etc.

Autonex cylindrical remote proximity switch PRD/PRDW series, the selection of self-developed special IC, with the highest international noise immunity level, high echo frequency, low leakage current and residual voltage, the detection interval is 1.5-2 times of the original product, close to the switch and the cable connection part of the selection of strong ...

A high-temperature pressure sensor is a sensor that converts pressure into an electrical signal output, which usually consists of two parts, namely a sensitive element and a conversion element. The sensitive element refers to the part of the sensor that can directly feel or respond to the measurement; The conversion element refers to the sensitive element in the sensor ...

Autonex has recently launched a new shading action form to add a space for users to choose. The BTF series of ultra-thin photoelectric sensors has a new dark ON form to increase the user's selection space. The selection of self-developed special IC, 3.7mm ultra-thin planning, suitable for small space ...

1. Air flow meter problem Problem characteristics: The vehicle is shaking at idle, high fuel consumption, weak at high speed, and black smoke from the exhaust pipe. View and dissect: through the fault diagnostic instrument detection, the engine air flow meter data block is seriously exceeded, the cause of the air flow meter damage, ...

BD series laser displacement sensor can measure the thickness, width, horizontal difference, parallax, twist and flatness of the target object by detecting the displacement. Regardless of the color or data of the policy, the sensor can provide accurate and stable measurement results. Sensor head and amplifier unit ...

First, the first component is blocked or the form of the device is wrong, and the pressure point is unreasonable, so we often emphasize that the device must be the correct device, once it is installed wrongly, or it is not well installed, it will bury endless hidden dangers for the back. What are the primary components? Orifice plates, remote transmission measuring joints, etc.

Cover the safety light curtain with your hands and observe whether the indicator light conversion is normal. During the use of the punch photoelectric protection device, the orientation of the photoelectric protection device shall not be changed at will. In the protection zone, block the light curtain by hand, ...

1. Measurement of action distance; When the action piece is close to the sensing surface close to the switch from the front, the distance close to the switch action is the action distance close to the switch, and the measured data should be within the parameters of the product. 2. Release distance ...

The PSK1 series is a two-stage display pressure sensor that displays the current value (PV) and the set value (SV) together. It not only shows the setting status, but also provides a power-saving form and a fine-tuning function to improve the user's convenience. PSK1 Key Features: Additional pressure scale (composite pressure ...

1) The detected object should not touch the proximity switch, so as not to damage the proximity switch due to friction and bumping; 2) Pull the lead wire of the switch by hand will damage the switch close, and it is best to fix the lead wire with a line card at 10 cm away from the switch when the device is installed.

1. Percussion hand pressure method It is common to encounter the phenomenon of good and bad operation of the instrument, and most of this phenomenon is due to poor contact or virtual welding. In this case, percussion and hand pressure can be used. The so-called "percussion" is to ...

SET button, which can be used to set the sensitivity. The basic principle of the sensor is to sense the refractive index of different media through a fiber optic probe, so as to obtain a digital signal, display it on the screen, and send the switching value by comparing the magnitude of the displayed value and the set sensitivity value. Indicator light when the sensor ...

Leveraging the expertise accumulated in the development of industrial sensors, such as area sensors and mapping sensors, Ottonix has developed the SFL series (standard) and SFLA series (high-performance) safety light curtain systems that comply with the leading international standards/regulations. The product has built-in fingers/hands/people ...

1. After the modulation pulse generated by the vibration circuit passes through the reflection circuit, the digital integration photoelectric switch or RC integration method is used to eliminate the disturbance, and finally the driver is triggered by a delay (or no delay) to output the photoelectric switch control signal. 2. Use optical elements to make the beam in the middle of the propagation medium.