Robot Dresspack Selection – KUKA Robots

1. Place the nut Clamp the quad or hex nut and place it in the fixture 2. Thread sizing Grab the screw and assist it to complete the "180-degree turn" action; Apply an appropriate amount of sealant to the thread on its underside ...

KUKA launched the KR C5 micro IP54 anti-oil mist protective cover, which escorts the efficient work of the KR C5 micro control cabinet in harsh environments such as dust and oil mist, and uses a super heat dissipation system to cool the control cabinet in the protective cover. ...

Robot manipulator structure Through the application of modern planning methods such as finite element analysis, modal analysis and simulation planning, the optimization planning of the robot operation organization is completed. Explore new high-strength, lightweight materials to further improve the load/weight ratio. For example, with the Germany KUKA company as the representative ...

(1) Teach: P6, P7, P8, P9, HOME Refer to P4 and teach P6 with LIN command: P3, P2 and Pl respectively, and teach P7, P8 and pg with PTP command; Return to the HOME point with the PTP command as shown, the end of the machine ...

The wiring and clarification of the corresponding interface are as follows: 1. X1 connector: power supply interface of control cabinet. (1) KR C4 stand & KR C4 Midsize & KR C4 Extend: three-phase four-wire system, 380V AC AC; ...

Fault Symptom: After the robot is turned on, the teach pendant shows KSS15101 fault code (the safety device is wrong in 5 safety nodes from 0 to 4 channels), and the robot cannot be put into operation normally. Fault Detection: First inspect the site ...

KUKA welding robot has stable performance, large working space, fast moving speed, strong load capacity, and the welding quality is significantly better than manual welding, which greatly improves the production efficiency of spot welding operations. Spot welding machine is mainly used for spot welding of automobiles. 　　With the development of the automobile industry, butt welding ...

For "online" measurement, the requirements consider that the components under test are affected by other parallel branches, and the measurement results should be analyzed and judged against the schematic diagram. "Offline" measurement requires the components or circuits under test to be repaired and desoldered from the entire circuit or printed board, which is more troublesome to operate.

When a robot assists in the care of patients as a component of a medical device, the robot is closely monitored: this is now possible in KUKA's new 3D virtual showroom. It's all about simulating an operating room with three animated robots. With just a few clicks, the ...

1. Understand the ontological structure of the robot The KUKA robot used in the workshop is composed of 6 axes, each axis is driven by 1 servo motor, and each axis of the robot is operated independently to control the servo motor to rotate forward and backward after powering on, and the single-axis operation is carried out in T1 mode. Second, choose the shaft to sit ...

Step 1: View the environment 1. Recognize the ambient temperature: The ambient temperature of the KUKA control cabinet is required to be between 5°C-45°C, the working environment temperature of the robot body is 10°C-55°C, and the working temperature of some new models is 0°C-55°C (see the robot skills manual for details).

Tactile sensors for industrial robots can help industrial robots measure any physical interaction with their environment. What are the functions of tactile sensors and the types of tactile sensors in industrial robots? 1. Optical tactile sensor Light...

KUKA Industrial Robot System Introduction, KUKA Robot Co., Ltd. was founded in 1898 in Augsburg, Bavaria, Germany, and is one of the world's leading industrial robot manufacturers. KUKA Robotics has more than 20 subsidiaries around the world, most of which are sales and service centers, ...

Before the servo positioning operation, it is generally necessary to perform the origin return first, otherwise the servo motor may be stopped, saying that it will be "started when the origin return is not completed". So, why origin regression? Origin back ...

The robot industry is a fast-growing industry in China for a period of time in the future, as one of the country's new strategic industries, robot skills reflect the comprehensive strength of national science and technology. From 2010 to 2013, the sales of industrial robots in China ...

1. Unplug the fan from the control panel. 2. Loosen the 4 screws and remove the back plate. 3. Remove the set screws from the socket. 4. Fold the piercing sleeve and pull out the connecting wire. 5. Take the fan bracket with the fan...

1. Archiving Channels: During each archiving process, a ZIP file is generated on the corresponding policy media Same name as the robot. The file name can be changed individually under the robot data. Storage Orientation: There are three different storage orientations to choose from: ...

Don't panic when there is a problem with the robot during the operation, if the problem is not caused by the controller, then the cause of the problem must be the damage to the machine parts. In order to deal with the problem as quickly as possible and in the simplest possible way, the problem should be analysed. And the need to find out which part is the lead ...

On the 21st, KUKA Industrial Robot and its Chinese brand ambassador, table tennis athlete Tim · Bohr, participated in the 29th China International Rubber and Plastics Industry Exhibition. The relevant person in charge of KUKA said that the Foshan market is very potential, and the market prospect is very good.

The functional characteristics of industrial robots affect the operating power and reliability of robots, and the following functional policies should be considered in the planning and selection of robots: (1) Leisure: Leisure: Leisure is the primary policy to measure the skill level of robots.