Overview of the seven axes of the robot – KUKA robots

1. Cartesian coordinate type (1) Advantages: This kind of operator has a simple structure, strong intuitive movement, and is convenient to achieve high precision. (2) Disadvantages: It occupies a large space and has a small working range. 2. Cylindrical coordinate type (1) Strengths: Same Cartesian coordinate type ...

1. It is necessary to conduct teaching assignments Before the robot performs active welding, it is necessary for the operator to teach the robot the track of the welding gun and set the welding conditions. Because it is necessary to teach, the robot does not weld to a wide range of products produced in a small number of products. 2. There must be ...

The robot control system is an important part of the robot, which is used to control the manipulator to complete specific work tasks, and its basic functions are as follows: 1. Recall function: store the order of work, the movement path, the movement mode ...

When calibrating the KUKA robot, the axes are moved to a defined mechanical orientation, i.e. the mechanical zero orientation. This mechanical zero point requires the shaft to move to a bearing that detects the notch or scribing symbol. If the KUKA robot is in the zero position of the machine, it will store the positive detection of each axis ...

After each change to the motion command, the robot program must be tested at low speed (run method T1). Immediately starting a robot program at high speed can cause damage to the robot system and the entire equipment, as unpredictable movements may occur. If someone sits dangerously ...

1. Problems in the load setting of KUKA robots In fact, there is only one purpose, the appropriate load, under the appropriate driving force, the manipulator can withstand the inertia moment that satisfies both static and dynamic, so as to ensure that the electrical control system controls the manipulator. and other machines ...

Berthold Hermle AG is one of the world's leading manufacturers of milling machines and machining centres. When it comes to the automation of its machining centers, Hermle relies on the expertise of KUKA Roboter GmbH from Augsburg. The company is charging in the new production system RS 4 ...

1) Rapidity. The time from obtaining the command signal to the completion of the required working state of the motor should be short. The shorter the time to respond to the command signal, the higher the sensitivity of the electric servo system, and the better the fast response function.

The transfer robot is a manipulator in practical work, and the manipulator is developed because its positive role is increasingly known: First, it can partially replace manual operation; Second, it can follow the requirements of the production process, follow the certain procedures, time...

1. The KUKA robot does not supply power and has no response 2. KUKA robot 1-6 axis, any axis does not move, stuck 3. The KUKA robot crashes and the KUKA robot computer cannot be started and the computer does not respond 4、KU ...

1. The button to unplug the smartPAD 2. Operation method selector switch: (1) With a key: The operation method can only be changed if the key is pierced. (2) Without a key: The connection manager can be called by selecting the switch by operating the method. Elapse...

When playing KUKA robots, it is often said that ABB has a waiting timeout instruction, why don't you KUKA have it? In fact, ABB only encapsulates the instruction, users use it directly, each language has its own characteristics, KUKA is open, as long as you understand the function of the logic yourself...

The structure of the robot with a straight tandem structure is simplified, as shown in the figure below. The six-axis straight tandem robot has six joint axes from A1 to A6, during which A1, A4, and A6 are rotary axes, and other A2, A3, and A5 are swing axes. The robot motion system attaches great importance to the end node of the robot motion chain.

1. Secure the robot so that it doesn't tip over 2. Move the connecting rod A2 in the "+" direction as far as possible 3. Remove the 4 screws and remove the CBS bonnet 4. Loosen the two M16x80-10.9 screws on the bearing block slightly ...

KUKA's Edition robot assists new customers in price-sensitive shopping malls in the useful automation of welding tasks. Focus on the main points, have a higher cost-to-benefit ratio, and can obtain the skill set at that time. Initially, the KR CYBERTECH nano ARC was available in two variants of the Editi ...

Why does the robot flutter when it is running? Please do the following: 1. Is it that the load data you entered is incorrect? If the load data is too high or too low, and the difference between the load and the practice load is too large, it will cause flutter! 2、 ...

Automation brings many advantages to businesses, especially when it comes to risk, strenuousness, or a single operation. However, there is often a programming challenge that needs to be solved. How can we easily teach the KUKA robot helper what it needs to do? Manually guided: KUKA ready2_pi ...

1) Comfort degree: This is an important goal that reflects the flexibility of the robot. Generally speaking, it is possible to reach 3 degrees of freedom in the robot working space, but welding must not only reach a certain position in the space, but also ensure the spatial attitude of the welding (cutting objects or welding tongs). Thus...

1. Move the gripper to an open area, stop all mechanical maintenance operations on the gripper, pay attention to safety! 2. Copy the "Program Pictures and Configuration Files" folder to a USB flash drive and plug it into the control cabinet 3. In SmartPAD...

Phenomenon 1: The direction of the finger does not coincide with the mouse arrow. Reason 1: After the driver is installed in the industrial robot teach pendant, when correcting the bearing, there is no pen directly touching the square position of the bull's-eye. Treatment 1: Correct the orientation from the beginning. ...