Yaskawa Robotics FAQs

1: Flange specification The cross-sectional size of the reducer is generally about the same as the cross-sectional size of the motor, and other parameters refer to the description of the selected brand, and the technical sample is generally marked with the selection steps and calculation examples. The specific model is indicated differently by brand. Usually in the output flange size or cross-sectional size ...

Spraying is another common process application of industrial robots, second only to welding process applications, and they all belong to high-intensity, high-precision, and high-sensitivity work tasks in harsh environments. The spraying process has extremely high requirements for the performance of the robot, of course, for the formulation of the process, ...

1. Power failure: If the servo drive has no power supply or the power supply is unstable, it will cause the motor to not work properly. The solution is to check the power supply line, confirm that the power supply line is normal and stable, and if the power supply needs to be replaced, select the appropriate power supply. 2. Control signal malfunction ...

1. Yaskawa robot teach pendant key switch to manual Teach mode - main menu - system information - security mode 2. Management mode - password - 999999999 3. Robot - Origin location 4. Open the door of the robot control cabinet and there is a mechanical prototype with 6 axes of the robot on the side.

First, the basic wiring The main power input is 220V, which is connected from L1 and L3 (the actual use should refer to the operation manual); The control power input r and t can also be directly connected to 220V; See pages 22 and 23 of the operation manual for motor wiring, and see the operation manual for encoder wiring.

Drive control Yaskawa Electric's Drive Control Division has achieved a leading position in the industry by integrating and commercializing various innovations and the world's latest technologies into inverters. These technologies have penetrated into various fields as world standards, and the quality, performance, ...

Fault analysis: the power line is out of phase Fault cause: Yaskawa servo motor factory is the default AC three-phase 200V power input, when connected to the single-phase 220V power supply, it will cause the servo driver to alarm A.F10 when the power is turned on. Troubleshooting: Set the servo parameter Pn00B to n.▢1▢ ...

The following are the common faults of the inverter and how to deal with them 1) OC Over Current This is the most frequent failure of the inverter, and it is divided into external and internal causes in the analysis of causes. External causes: mechanical structure and parameter setting, open-loop control ...

China's industrial manipulator (15.620, 0.00, 0.00%) market capacity continues to develop, and overseas robot manufacturers have surged production capacity to solve China's requirements. As one of the "four families" of intelligent robots, Yaskawa Electric has accelerated the rational layout of Chinese artificial intelligent sales market, ...

It is an all-in-one controller with built-in power supply, CPU, communication and servo control. From simple positioning and interpolation to advanced multi-axis control, we are looking for cost-effective devices. Compatible with open networks Just install the optional module in the slot, which not only corresponds to the open network, but also ...

High-voltage and high-power variable frequency speed control devices are widely used in various fans, pumps, compressors, rolling mills, etc. in large-scale mining production plants, petrochemical industry, municipal water supply, metallurgical steel, power and energy industries. In metallurgy, chemical, electric power, municipal water supply and mining and other industries...

In order to realize the anti-collision function of Yaskawa robots, there are two ways to connect external sensors, which are described below; In addition, how to dismiss alarms will be described in this article. 01. Directly connect to an external collision sensor 1. The machine in the door of the control cabinet ...

The fault code is CF refers to Control Failure, which reaches the torque limit for more than 3 seconds in the deceleration stop (no PG vector control mode) Possible reasons are: The motor parameters are not set correctly The set value of the torque limit is too small The load inertia is relatively ...

(1) Overcurrent, display character: OC. The reason for tripping is the short circuit of UVW at the output end, the load is too large, the acceleration/deceleration time is set incorrectly or the torque is unreasonable, resulting in overcurrent or overheating of the main circuit module. Check whether there is a short circuit in the motor junction box, whether the motor winding is to the ground, phase to phase ...

Servo motor refers to the engine that controls the operation of mechanical components in the servo system, and is a kind of auxiliary motor indirect transmission device. The main function is to use it in a closed ring, transmit the signal to the system at any time, and at the same time correct its own operation with the signal given by the system. Servo motor ...

Yaskawa Electric is a professional manufacturer in the field of motion control, is the first company in Japan to do servo motors, its products are known for stable and fast, cost-effective, is the world's largest sales, the most used servo brand. In China, Yaskawa Servo has occupied the largest market for many years ...

One. The type of failure and the reason for the failure 1. The type of failure Faults are divided into power supply faults, internal faults, and load faults. Power failure: There is a fault in the power grid connected by the inverter Internal fault: The failure of the drive itself Load Failure: ...

1. It may be that the capacity of the servo unit does not match the capacity of the servo motor. 2. It may be that the servo unit is faulty. 3. It may be outside the range of parameter settings. 4. It may be that the set value of the electronic gear ratio is outside the set range. ...

1. First turn off the power - and pull down the power switch. 2. Secondly, use a pen to check the voltage feedback line of the cable behind the base of the robot to see if it is connected or loose. 3. Finally, confirm the abnormality for maintenance. Other error alarm codes can also be used according to the abnormal message under the welder...

1. Different control methods Stepper motor: The rotation angle is controlled by controlling the number of pulses, and one pulse corresponds to one step angle. Servo motor: The angle of rotation is controlled by controlling the length of the pulse time. 2. The workflow is different Stepper Motor: Stepper ...