Yaskawa servo motor MP2300/MP2310/MP2300S function introduction

1, Maybe the connection of the external resistor is bad, falling off and disconnecting will cause an alarm, we can check the wiring. 2. It may be that the jumper wire of the resistor connection terminal B2-B3 falls off, and then check if the jumper wire falls off. 3. It may be that the resistor capacity ...

Yaskawa Robot is a well-known robot manufacturer in the world, it is one of the four major robot families, and has launched Yaskawa MH24, it is a multi-functional robot, which is widely used in industrial production, and the following look at Yaskawa MH24 handling robot maintenance routine inspection. ...

Yaskawa Electric, one of the world's largest manufacturers of industrial robots, announced a 150% year-on-year increase in net profit for the six months ended Sept. 30. The Japan company announced that the company reported a profit for the quarter due to the demand for its industrial robots in China, Japan and United States.

1. Due to the soft material of the bolt material inside the Yaskawa inverter, if the tool is matched with a large error, it is easy to cause damage to the bolt head, it is recommended to equip the maintenance personnel with special tools of imported or joint venture brands. 2. The electrolytic capacitor and heat sink are made of aluminum alloy.

Yaskawa servo drives are used to control servo motors, which are similar to AC motors and are part of the servo system. The servo drive takes the digital signal processor as the control core, which can realize more complex control algorithms and realize digitalization, networking and intelligence. The present invention adopts the wisdom ...

A.F10: Power line is out of phase (the low voltage state of one phase of R, S, and T phases lasts for more than 1 second in the state of the main circuit power supply ON) Cause: Poor wiring of three-phase wires The three-phase power supply is unbalanced Single-phase AC power input is not set (Pn00E ...

1. First, confirm the alarm code. The alarm code is different for each servo drive, so you need to consult the corresponding equipment manual or contact the manufacturer for a specific list of alarm codes. 2. Determine the cause of the fault according to the alarm code. Different alarm codes correspond to different fault types, which can be ...

China's industrial manipulator (15.620, 0.00, 0.00%) market capacity continues to develop, and overseas robot manufacturers have surged production capacity to solve China's requirements. As one of the "four families" of intelligent robots, Yaskawa Electric has accelerated the rational layout of Chinese artificial intelligent sales market, ...

(1) The E end of the high-voltage inverter should be connected to the shell of the control cabinet and the motor, and should be connected to the ground, and the grounding resistance should be less than 100Ω, which can absorb surge interference. (2) The input or output of the high-voltage inverter is equipped with an inductive magnetic ring filter. Flat and 3-4 turns, helps to inhibit ...

1. Open the parameter setting interface of the servo drive and find the invert parameter setting option. 2. Set the inversion parameters, including the inversion voltage, inversion speed, etc. Depending on the specific situation, the reversal voltage can be set to -10V and the reversal speed to 1000RPM. 3. After saving the settings ...

1 Introduction Over the years, Yaskawa has accumulated very rich experience in the petroleum industry, such as G7/P7/F7/G5/P5/G5HHP/VS and other different series of inverters have been widely used in OEMs, the main fields are centrifugal separators, pumps, fans, transportation equipment ...

Set it in the controller's parameter settings. 1. Connect the computer and the controller to enter the parameter setting interface. 2. Find the parameters of the number of servo fault retries or FaultRetryCount. 3. Set it to the required number of retries, which is usually recommended to be set to 1— ...

1. No-load power-on test of inverter 1. Ground the grounding terminal of the inverter. 2. Connect the power input terminal of the inverter to the power supply through the leakage protection switch. 3. Check whether the factory display of the inverter display window is normal, if it is incorrect, it should be reset, otherwise ...

11. Robot jitter? Diagnostic process: Due to the difference between the jitter area and the amount of jitter, the diagnosis of jitter becomes a difficulty. At this stage, the diagnostic method is to replace the amplifier, replace the motor, and replace the reducer one by one. Improvement method: ...

1. It occurs when the power is turned on It's a servo unit fault 2. On servo on is happening It is an abnormal wiring of the motor (there is a connection problem or there may be a wrong wire, I encountered a wrong phase) 3. The encoder wiring is abnormal Servo unit failure 4. Re-enter the finger ...

Not long ago, it was found from the national enterprise information management system that the joint venture industrial manipulator enterprise founded by Midea and Yaskawa Electric announced the record cancellation/announcement information on April 12, and had already established a liquidation team to accept debt applications. The joint venture is a joint venture in Guangdong ...

1. The correct shielding grounding point is at the reference potential point inside the circuit, which depends on whether the noise source and the receiver are grounded or floating at the same time. 2. Make sure that the shield is grounded at the same point so that the ground current will not flow through the shield. 3. Avoid multiple connections ...

1. Controller The controller is mainly responsible for issuing and transmitting action instructions, controlling the movement position, posture and trajectory of industrial robots in the workspace, operation sequence and action time. The controller is divided into hardware structure and software structure. In terms of hardware, the current market has ...

Yaskawa H1000 series is available in the following models H1000 Series Heavy Load 1. CIMR-HB4A006FAA/FAC/FBC 1·5KW H1000 replaces G7 series 2、CIMR-HB4A0075 30KW 3、CIMR-HB4A0045AAA 4、CIMR-HB4A0005FAA/FA ...

1. Automobile manufacturing: In the automotive manufacturing industry, Yaskawa Robot GP180 can be used for welding, dispensing, cutting, and assembly, etc. 2. Electronics industry: In the electronics industry, Yaskawa Robot GP180 can be used for semiconductor chip production, mobile phone assembly, etc. 3. Food ...