What are the fault codes of Yaskawa inverter

1, Maybe the connection of the external resistor is bad, falling off and disconnecting will cause an alarm, we can check the wiring. 2. It may be that the jumper wire of the resistor connection terminal B2-B3 falls off, and then check if the jumper wire falls off. 3. It may be that the resistor capacity ...

Yaskawa inverter V1000 series has amazing performance, wide range of uses, simple use and maintenance, and user-programmed function, breaking through the previous small inverter in every aspect and improving the level of all small machines. 1 multi-purpose (synchronous motor can also be driven). Detergent ...

1. Check whether the power wiring is in good contact, and if the contact is bad, you need to unplug the power supply and re-wire. 2. Check whether the wiring between the servo drive and the host is in good contact, and if the contact is bad, the wiring needs to be removed and rewired. 3. Check the connection between the main machine and the servo drive.

Yaskawa Electric is a professional manufacturer in the field of motion control, is the first company in Japan to do servo motors, its products are known for stable and fast, cost-effective, is the world's largest sales, the most used servo brand. In China, Yaskawa Servo has occupied the largest market for many years ...

First, the servo dispute settings are too large, and it is recommended to readjust the servo parameters manually or automatically. Second, make sure that the initial value of the time constant of the velocity feedback filter is set to zero, and try increasing the initial value. Thirdly, the electronic gear ratio setting is too large, it is recommended to restore ...

Yaskawa inverter Uv1 fault name: main circuit undervoltage If the operation command is not entered (the inverter is stopping), the following conditions occur. 1. The DC voltage of the main circuit is lower than the set value of L2-05 (the detection value of the undervoltage (UV) of the main circuit). 2. 200V class: about 190V ( ...

1. Encoder malfunction. When the power is turned on again and this alarm still occurs, it is possible that the servo motor is faulty, and the servo motor is replaced; 2. Encoder malfunction due to noise and other interference. Correct handling of the wiring around the encoder (separating the encoder cable from the servo motor ...

The following are the common faults of the inverter and how to deal with them 1) OC Over Current This is the most frequent failure of the inverter, and it is divided into external and internal causes in the analysis of causes. External causes: mechanical structure and parameter setting, open-loop control ...

Advantages of Yaskawa Industrial Robots 　　Generalization Programmable industrial robots that support multiple degrees of freedom of motion make the application more flexible. Although not human, compared to many general-purpose industrial automation aircraft (a class dedicated to industrial applications or customized mechatronic solutions), ...

1. Determine mechanical specifications, load, rigidity and other parameters; 2. Confirm the action parameters, stroke, accuracy, acceleration and deceleration time, cycle, moving speed, etc.; 3. Select motor inertia, load inertia, motor axis conversion inertia, and rotor inertia; 4. Select the motor back ...

1. Specifications and parameters of the motor The inverter drives the motor during use, so the inverter can be selected from the perspective of the motor to select the model and specification. First of all, we must first understand the specifications and parameters of the motor. You can use Yaskawa inverter ...

In terms of speed: the servo motor + ball screw mode may resonate due to the change of load and mechanical design and installation when running at high speed, and the speed will be limited; The linear servo motor belongs to the direct drive, so the only factor that affects the speed is the linear servo motor itself.

Analysis of the fault code of Yaskawa inverter, for reference only: OC Overcurrent The output current of the inverter exceeds the overcurrent detection value · GF grornd Favlt Grounding The ground current on the output side of the inverter exceeds 50% of the rated output current of the inverter ...

1. The cause of the failure may be that the power plug is not plugged in properly. Solution: Check and plug in the power plug. 2. The sensor is damaged and the resistance value is wrong. Solution: Replace the sensor. 3. The fuse is blown out. Solution: Repair and replace the fuse ...

Q: How often is the robot maintained? A: Generally speaking, the frequency of scheduled maintenance of the robot should be determined on a case-by-case basis. It is generally recommended to carry out a full maintenance every 3-6 months, but for high-intensity and long-working robots, more frequent maintenance may be required.

A.020 A.02 User Parameters and Number Check Abnormalities The data of the internal parameters of the servo unit is abnormal A.021 A.02 Parameter Formatting Abnormality The data of the internal parameters of the servo unit is abnormal A.022 A.02 Abnormal system parameters and number check The data of the internal parameters of the servo unit is different ...

When the Yaskawa inverter fails, the operator will display the fault content, cut off the output, and the motor will decelerate and stop freely. The following is a description of the fault alarm code of Yaskawa inverter and the corresponding fault reason, which is for reference only. OC Overcurrent ...

1. First, confirm the alarm code. The alarm code is different for each servo drive, so you need to consult the corresponding equipment manual or contact the manufacturer for a specific list of alarm codes. 2. Determine the cause of the fault according to the alarm code. Different alarm codes correspond to different fault types, which can be ...

(1) Memory function: store operation sequence, motion path, motion mode, motion speed and information related to production process; (2) Teaching function: offline programming, online teaching, indirect teaching. There are two types of online teaching: teaching box and guided teaching; (3) With ...

1. Enter the editing mode of Yaskawa robot first 2. Select "Function Effective Setting" for setting 3. Select "Allow" to start the appointment 4. Click Settings to enter "Appointment Activation (Connection)" 5. Set the input signal and output signal you need.