Yaskawa inverter fault code description and corresponding fault causes

The full name of Yaskawa inverter is "Yaskawa AC inverter governor", which is mainly used in three-phase asynchronous AC motors to control and adjust the speed of the motor. Yaskawa inverter is famous all over the world and has a very high share in the Chinese market for many years. Motor knowledge derived from Yaskawa Electric's input, ...

1. The inverter shows that SC refers to the drive fault. 2. Cause of failure: 1. The output side of the inverter is interphase or short circuit to the ground. 2. The inverter module is damaged. 3. Handling method: 1. Remove the load, power on normally and turn on the machine, check if there is a three-phase ...

1. Motor encoder alarm 1. The cause of the failure (1) Wrong wiring; (2) electromagnetic interference; (3) Encoder hardware damage caused by mechanical vibration; (4) Pollution caused by the on-site environment; 2. Troubleshooting (1) Check the wiring and eliminate the error ...

The main functions of the industrial robot controller The controller mainly solves the forward kinematics and inverse kinematics of the robot to help the robot complete the trajectory planning. The controller of the industrial robot is composed of controller hardware and controller software.

Yaskawa robot is a kind of industrial robot, which can be applied to various automated production lines according to its specifications and models, and the high-temperature work workshop is a major field where industrial robots are used more, so it needs to be protected by robot protective clothing. The following is a brief introduction to Ontor ...

01. The robot switch often jumps or can't close? Cause: 1. Aging of switches; 2. The switch selection is wrong; 3. The pump is stuck or the motor is short-circuited; 4. The line is aging, short circuit, the line is too small or the phase is missing. Solution: ...

1. The cause of the failure may be that the power plug is not plugged in properly. Solution: Check and plug in the power plug. 2. The sensor is damaged and the resistance value is wrong. Solution: Replace the sensor. 3. The fuse is blown out. Solution: Repair and replace the fuse ...

1. Check whether the power wiring is in good contact, and if the contact is bad, you need to unplug the power supply and re-wire. 2. Check whether the wiring between the servo drive and the host is in good contact, and if the contact is bad, the wiring needs to be removed and rewired. 3. Check the connection between the main machine and the servo drive.

Japan's Yaskawa Electric famously created the first all-electric industrial robot, Motoman, in 1977, headquartered in the city of Kita-Kyushu, since its establishment in 1915, has gone from being called "Yaskawa Electric Japan as an automobile manufacturer", "Yaskawa Electric Automation Company of Japan" to "...

Not long ago, it was found from the national enterprise information management system that the joint venture industrial manipulator enterprise founded by Midea and Yaskawa Electric announced the record cancellation/announcement information on April 12, and had already established a liquidation team to accept debt applications. The joint venture is a joint venture in Guangdong ...

1. When the oscilloscope checks the current monitoring output of the driver, it is found that it is all noise and cannot be read; Cause of failure: The current monitoring output is not isolated from the AC power supply (transformer). Solution: It can be detected and observed with a DC voltmeter. 2. Motor ...

Before starting the machine, you need to check the following items. Machine tools: Confirm that when the four machine tools are empty, the signal sent by the two first-sequence machine tools is the first piece loading signal M28, and the signal sent by the two second-sequence machine tools is the first piece loading signal M28. Robots start with ...

1. First press "MENU to set collision detection". 2. Secondly, the collision detection status: set to enable for the collision detection to be effective. 3. Final sensitivity: set the range from 1% to 200%, and the default setting is 100% ...

High-voltage and high-power variable frequency speed control devices are widely used in various fans, pumps, compressors, rolling mills, etc. in large-scale mining production plants, petrochemical industry, municipal water supply, metallurgical steel, power and energy industries. In metallurgy, chemical, electric power, municipal water supply and mining and other industries...

When the crane is working, the start and stop of the cart and trolley mechanism, as well as the acceleration and deceleration process, will cause the suspended load to swing, which not only reduces the production efficiency but also brings great safety hazards to the staff and related equipment. And Yaskawa Electric has been deeply involved in ...

The following are the common faults of the inverter and how to deal with them 1) OC Over Current This is the most frequent failure of the inverter, and it is divided into external and internal causes in the analysis of causes. External causes: mechanical structure and parameter setting, open-loop control ...

Explosion-proof grade of robot for spraying use? Compliant with TIIS, FM, ATEX, and KCs standards, please check the relevant catalogs for details. How do I download the relevant manual for the robot? At present, the download of the manual is not provided, and the manual comes with the robot, so please keep it properly. ...

1. Yaskawa servo alarm A840 (A84) is: encoder data error alarm. A.84 Common causes of alarm are: 1. Excessive mechanical vibration 2. High-frequency noise in the application environment 3. Servo motor inlet water inlet oil, dust, etc 4. The driver is faulty ...

Industrial robot is a multi-degree of freedom machine device, can automatically perform work, according to its own power and control ability to achieve various functions, by the mechanical part, sensing part, control part and other three parts, these three parts are divided into six subsystems, namely: 1. Drive...

Excellent motor drive function Advanced motor drive skills All motors can be controlled – whether they are driving induction motors or synchronous motors (IPM motors/SPM motors) – with high utility current vectoring. Inverters for induction and synchronous motors ...