Buke servo motor - servo motor encoder fault and maintenance

1. Surface acoustic touch screen. (1) Fault 1: Touch deviation Symptom 1: The position of the finger does not coincide with the mouse arrow. Reason 1: After installing the driver, there is no vertical touch of the bullseye center position when the position is corrected. Solution 1: Recalibrate ...

1. Fault code: E-01, E-02 Significance: The parameters are initialized incorrectly during power-on. Cause: Incorrect parameter settings. Solution: Power back on, if the fault is still reported, you need to force the parameter initialization, if it is repeated many times, it cannot be solved.

1. Adopt a power supply with excellent performance to suppress the interference introduced by the power grid. For the power supply supplied by the PLC controller, the non-power line power supply should be adopted, and the special line power supply should be used directly from the main bus of the low-voltage distribution room. Isolation transformers are selected, and the transformer capacity should be larger than the actual needs.

MT4000 series MT4000 series HMI is a sub-series of eView HMI, which is one of Buke's HMI products Series, human-machine interface MT4000 is referred to as ordinary application series. MT4000 series HMI products adopt 32 ...

B3: The base has feet. The end cap has no flange. Mounted on foundation members. B35: The frame has feet. Flange on the end cap. The flange has through holes. It is installed on the foundation member by a foot and attached to the flange mounting. B34: The frame has feet. The end cap has a flange and a screw on the flange.

1. Servo motor encoder is a product installed on the servo motor, which is equivalent to a sensor. 2. Do speed closed-loop and azimuth closed-loop to complete accurate speed regulation and accurate azimuth control. 3. The servo motor has its own encoder, which can be converted into servo electronic gears.

1. For new or long-term out-of-service motors, the insulation resistance between the windings and the windings to the ground should be checked before use. Usually for motors below 500V, 500V insulation resistance meter is used; 1000V insulation resistance meter for 500-1000V motors; 2500V insulation resistance meter for motors above 1000V. Insulated ...

1. Shake the meter, 500V can shake the meter, and shake the insulation resistance of the line on the three binding posts to the motor shell, which should be above 0.5M ohm, which means that there is no short circuit to the ground (Yantai motor maintenance). 2. Multimeter measurement: measure the resistance between the three phases of A/B/C, whether it is equal, it should be about the same...

Buke MK series all-in-one machine on the market for more than a year, received unanimous praise from many customers, in the Buke "quality first" to create an end-to-end full life cycle product quality management system" and "demand management" under the internal and external drive, through the application feedback of this series of products and in order to fit more ...

1. The basic design principle of user-centered In the design process of the system, the designer should grasp the characteristics of the user and discover the user's needs. In the whole development process of the system, it is necessary to continuously solicit the opinions of users and consult with users. The design decision of the system should be combined with the user's work.

1. Clean the motor and remove the dust and sludge outside the motor base in time. If there is a lot of dust in the environment, it is best to clean it once a day. 2. Check and wipe the motor terminals. Check whether the junction box wiring screws are loose or burned. 3. Check the screws of each fixing part, ...

1. In the daily inspection, the lubrication system, appearance, temperature, noise, vibration and abnormal phenomena are mainly checked, and the ventilation and cooling system, sliding friction and fastening of each component are also checked, and the inspection records are carefully made. 2. During the monthly or regular inspection, the main inspection ...

1. When the motor rotates, the LED light flashes (1) Cause of failure: HALL phase error. Solution: Check whether the motor phase setting switch is correct (2) Fault cause: HALL sensor failure, treatment method: When the motor rotates, detect the voltage of HalA, HalB, HalC ...

Material metering The measurement of powdery materials is commonly used in the way of screw measurement. The purpose of measurement is achieved by the number of turns of the screw rotation. In order to improve the accuracy of measurement, the speed of the screw is required to be adjustable, and the position positioning is accurate.

The main components of the motor include: 1. a frame; 2. an iron core; 3. a winding; 4. an end cover; 5. a bearing; 6. Centrifugal switch or starting relay and PTC starter; 7. a nameplate. 1 frame The frame structure varies depending on the cooling method, protection type, installation method and purpose of the motor.

In the past industrial field, HMI touch screens were used more as a window for people to interact with mechanical equipment, and were used to connect various PLCs and sensors. Nowadays, in the context of the Industrial Internet of Things, manufacturing enterprises need to integrate OT and IT technologies more to achieve their own digital and intelligent transformation.

1. Please ensure that the environment is clean and avoid oil. When used in dusty and humid places, although the protection level of the servo motor is very high, it will be easy to cause problems if it is often used in such an environment. 2. Regularly check the use of the servo motor to see if there is any damage outside.

Common models of Buke inverters 　　Buke CV100 series mini inverter The output frequency is 0-300Hz The carrier frequency is up to 15kHz, which effectively reduces the noise of the inverter It is equipped with RS-485 communication port as standard and supports Modbus communication protocol Sleep/wake function, inner ...

1. Sweeping: Sweeping is generally caused by friction of the stator and rotor due to bearing damage, shaft bending, or improper assembly during maintenance. In the process of overhaul and assembly of the motor, the parts of the motor should be kept clean, and the assembly of the end cover, bearing, etc. should be reasonable and not barbaric construction, otherwise ...

1. Initialize parameters Before wiring, initialize the parameters. On the control card: Select the controller Style; Reset the PID parameter to zero; When the controller card is powered on, the enable signal is turned off by default, and this state is saved to ensure that the controller card is powered on again and the time force is in this state. Serving ...